Intel NUC7i3BNK Bedienungsanleitung
Lies die bedienungsanleitung für Intel NUC7i3BNK (9 Seiten) kostenlos online; sie gehört zur Kategorie Grill. Dieses Handbuch wurde von 30 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 15.5 Bewertungen. Hast du eine Frage zu Intel NUC7i3BNK oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/9
Intel NUC Kit NUC7i5BNK NUC7i3BNK User Guide &
1
Intel®
NUC Kit
NUC7i5BNK
Intel®
NUC Kit
NUC7i3BNK
User
Guide
Intel NUC Kit NUC7i5BNK NUC7i3BNK User Guide &
2
Before You Begin
CAUTIONS
The procedures in this user guide sume familiarity with the general terminology associated with as
personal computers and with the safety practices a regulatory compliance required for using nd
and modifying electronic equipment.
Disconnect the computer from its power so ce and from any telecommunications link or netwo before ur rk
performi any of the procedures described in this guide. Failure to disconnect power, ng
telecommunications nks, or orks before you open the computer or perform procedures can li netw any
result in personal injury or equipment damage. Some circuitry on the board can continue operate to
even though the front panel power bu on is f.tt of
Follow these guidelines before you begin:
Always follow the steps in each procedure in the correct order.
Set up a log to record information about your computer, such as mo l, serial numbersde ,
installe tions, an conf at n informat d op d igur io ion.
Electrostati ischarge (ESD) can damage components. rform the procedures describe in c d Pe d
thi ch tes ap r onl at an ESD workstat n ing an a tatic wr t strap and a conductive foam y io us ntis is
pad. If such a stat n is not available, you n provide some ESD protection by wearing an io ca
antistatic wrist strap and attaching to a metal part of the computer chassis. it
Installation Precautions
When you inst an test the I e NUC, observe l warning an caut ns in the installat n all d nt l al s d io io
instruct ns. io
To avoid injury, be careful of:
Sharp pins on connecto rs
Sharp pins circuit boards on
Rough edges and sharp corners on the chassis
Hot components (such as SSDs, processors, voltage regulators, a heat sinks) nd
Damage wires that could cause a short circuit to
Observe l rning caut ns that instruct you fe computer serv ng to qualifal wa s and io to re r ici ied
tec perso el. hnical nn
Observe Safety and Regulatory Requirements
If you do not f w instruct ns, you increase your safety risk and the possibility of ollo these io
noncom iance wipl th regional laws and regul ions. at
Intel NUC Kit NUC7i5BNK NUC7i3BNK User Guide &
3
Thi guide s you w to: s tell ho
•
Install an M.2 SSD
•
Install and remove mory me
•
Install a VESA mount bracket
•
Connect power
•
Install an operating system
•
Install the latest device drivers and software
Open the Intel NUC Chassis
To open the Intel NUC chassis, follow these steps:
1. Unscrew the four corner screws on the bottom cover of the chassis and lift the cover.
Install a M.2 SSDn
Intel NUC Kits NUC7i3BNK and NUC7i5BNK support 80mm, 60mm, and 42mm M.2 SSDs. For a list of
tested M.2 SSDs, go to page on the Support site. the Tested Peripherals
Observe the precautions in "Before You Begin" on page 2.
If you are installing an 80mm M.2 SSD:
1. Remove the small silver screw from the 80mm metal standoff on the motherboard (A).
2. Remove the standoff from the 42mm position (B).
3. A gn the small notch at the bo om edge of the M.2 card with the key in the connector. li tt
Produktspezifikationen
| Marke: | Intel |
| Kategorie: | Grill |
| Modell: | NUC7i3BNK |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Intel NUC7i3BNK benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Grill Intel
9 August 2024
7 August 2024
7 August 2024
6 August 2024
6 August 2024
28 Mai 2024
25 Februar 2024
29 November 2023
9 November 2023
18 Juni 2023
Bedienungsanleitung Grill
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025