Intermatic ET2745C Bedienungsanleitung
Intermatic
Nicht kategorisiert
ET2745C
Lies die bedienungsanleitung für Intermatic ET2745C (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 2 Bewertungen. Hast du eine Frage zu Intermatic ET2745C oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
Electronic 4-Circuit
365/7-Day Time Switch
Installation and Setup Instructions
With 100-Hour Backup
Federal Communications Commission (FCC) Notice for ET2000 Series Time Switches
Description
This document explains the setup and conguration of the Intermatic ET2745
4-Circuit Electronic 365/7-Day Time Switch. The ET2745 time switch
automatically switches loads according to the according to the entered weekly
schedule. The time switch can support up to 48 xed ON and 48 xed OFF
events (96 total). Each xed event can be applied to any combination of circuits
and days.
The time switch features an LCD and panel-mounted control buttons to set,
review, and monitor the time switch functions, including setting date and time,
schedule creation, enabling or disabling Daylight Saving Time (DST) and
conguring DST switchover dates.
Follow these instructions to complete the installation and programming of the
ET2745 time switch.
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference, including interference that may cause
undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and radiates radio frequency energy and, if
not installed and used in accordance with instructions, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference that requires the user to correct at his or her own expense.
MODELS ET2745C, ET2745CR, ET2745CP
Shown in indoor/outdoor
lockable metal enclosure
NOTICE
• Do NOT touch circuit board components, contact can create a static discharge, which can damage these electronic components.
• Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing.
• More than one circuit breaker or disconnect switch may be required to de-energize the equipment before servicing.
• For plastic enclosures, bonding between conduit connections is not automatic and must be provided as part of the installation.
• Installation and/or wiring must be in accordance with National and Local Electrical Code requirements.
• Use #14-#8 AWG wires, rated at least 105°C - COPPER conductors ONLY.
• If the power disconnect point is out of sight, lock it in the OFF position and tag it to prevent unexpected application power.
• Make sure there is no wire insulation under the terminal plate on the time switch connector. Firmly tighten terminal screws.
• For outdoor locations or wet locations (rain-tight), conduit hubs that comply with requirements of the UL514B (standard for fitting conduit and
outlet boxes) are to be used.
• Do not remove insulator that is covering terminals.
• Do NOT exceed maximum current carrying capacity.
• KEEP DOOR CLOSED AT ALL TIMES when not servicing.
Risk of Fire or Electric Shock
WARNING
Snap out catch
Tilt top forward
Installation
Follow these instructions to install the time switch.
1. Open the time switch enclosure door.
2. Remove and retain the screw that secures the plastic insulator.
3. Lift the left side of the plastic insulator and pivot away to expose the terminal strip.
4. Press the latch at the top of the enclosure and pull out the mechanism from the
enclosure.
5. Choose and remove the selected knockout(s) from the enclosure.
NOTE: There are ve 1/2 inch to 3/4 inch combination knockouts available. There are
two on the bottom of the enclosure, one on each side, and one on the rear. If a 3/4
inch knockout is needed, remove the 1/2 inch knockout rst, then the 3/4 knockout.
6. Place the enclosure in the desired location providing space for the enclosure door to
swing open fully.
7. Securely mount enclosure using provided mounting holes.
8. Use appropriately rated ttings for the installation.
9. Snap the mechanism back into the enclosure.
10. Strip 1/2 inch off the supply and load wires. Use AWG #14 - #8 copper conductors
rated at least 105ºC. Torque to 15.6 lbf-in.
11. Connect the wires to the proper terminals on the time switch and tighten the screws
rmly (See wiring diagrams).
12. Connect ground wire to grounding terminal at the bottom of metal enclosures.
13. Return the insulator to its original position and replace the screw.
14. Close enclosure door.
15. Apply power to the time switch.
1/2 inch
Wiring Diagrams
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
OUTPUT
1&2
OUTPUT
3&4
OUTPUT 1
OUTPUT 2
OUTPUT
3&4
OUTPUT 3
OUTPUT 4
OUTPUT
1&2
OUTPUT 4
OUTPUT 3
OUTPUT
1&2
OUTPUT
1&2
OUTPUT
3&4
AC IN
NO-1 COM1 NO-2 COM2 COM3NO-3 COM4NO-4
CIRCUIT 1 CIRCUIT 2 CIRCUIT 3 CIRCUIT 4TIMER
POWER
L1
L2/N
TIMER CONFIGURATION FOR TWO CONTACTOR CONTROLS
OUTPUT CONFIGURATION: PUL - CIRCUIT 1 AND 2
OUTPUT CONFIGURATION: PUL - CIRCUIT 3 AND 4
COM
CLOSE
OPEN
COM
CLOSE
OPEN
Produktspezifikationen
| Marke: | Intermatic |
| Kategorie: | Nicht kategorisiert |
| Modell: | ET2745C |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Intermatic ET2745C benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Intermatic
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Avantco
- Aeotec
- Polisport
- Hoshizaki
- Power Dynamics
- Malmbergs
- Pfannenberg
- Fagor
- Anslut
- Imperial
- EA Elektro Automatik
- SwitchBot
- Ultimate
- DBX
- Reer
Neueste Bedienungsanleitung für -Kategorien-
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025