Inverto Black Pro Bedienungsanleitung

Lies die bedienungsanleitung für Inverto Black Pro (4 Seiten) kostenlos online; sie gehört zur Kategorie Schalter. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 9 Bewertungen. Hast du eine Frage zu Inverto Black Pro oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Technical parameters

Inputs4 x IF inputs from Quattro LNB

1 x UHF/VHF input from Terrestrial antenna

Outputs4 x loopthrough satellite IF outputs

1 x loopthrough terrestrial output

1 x Legacy output to connect to legacy receiver with combined

terrestrial signal

1 x Unicable output to connect up to 8 receiver tuners with com-

bined terrestrial signal

Frequency rangeSatellite: 950-2150MHz

Terrestrial: 47-862MHz

Loopthrough lossSatellite: max -3dB

Terrestrial: max -3dB

GainSatellite: 10dB (min)

Terrestrial: no amplification

IsolationSatellite-Satellite outputs: min 30dB

Satellite-Terrestrial : min 35dB

Control protocolDiSEqC™ commands extension according to CENELEC

prEN50494

Power consumption20VDC, 380mA

Dimensions (W x H x D mm)W=138.82 H=203.2 D=18.74 mm

Temperature range-20C - +60C

AC/DC adaptorInput voltage: 90-265VAC, 50/60Hz

Output voltage: 20VDC

Output current: 600mA

Short circuit protection: None

Troubleshooting

Make sure the satellite antenna and LNB are properly fixed, connected and adjusted and that the sat-

ellite receivers are installed, connected and switched on according to available instructions.

Ensure there is no short circuit on the product inputs. This will prevent power to the LNB. If this is the

case, disconnect the product from the main power, and then find and remove the short circuit on the

product inputs. Then re-connect the multiswitch to the main power.

Frequent defects are in connector joints i.e. if the central conductor is too short and fails to make

contact in the connector. Also the shielding braid should make proper contact with the connector coat.

Sometimes a reset to the multiswitch microprocessor is sufficient to remove a fault: simply disconnect

the multiswitch from main power for 30 seconds and then reconnect again.

If you are unable to remove the fault yourself, please contact your distributor.

Disposal

Following relevant EU directives, this device shall not be disposed of together with municipal waste.

Use local waste collection and recycling systems to dispose wore out products.

*

DiSEqC™ is a registered trademark of Eutelsat

*

For purpose of brevity, some product descriptions in this sheet remain at platform level and may not be

referred to as detailed datasheets of the products. Inverto Digital Labs reserves the right to amend, omit or

add products, product-lines, and/ or features without notice.

Installation manual

Unicable

™

Multiswitch

IDLP-UST111-CU010-8PP

4

V100214

Power In

20V DC, 380mA

V/HH/L H/H

Terrestrial

input

Satellite - Input

V/L

Terrestrial

input

Satellite - Input

V/HH/L H/HV/L

Terrestrial

output

Unicable Cascadable Switch

IDLP-UST111-CUO1O-8PP

Item: 3702

User Bands:

0 : 1076.06MHz 4 : 1484.30MHz

1 : 1178.12MHz 5 : 1586.36MHz

2 : 1280.18MHz 6 : 1688.42MHz

3 : 1382.24MHz 7 : 1790.48MHz

Satellite inputs: IF 950-2150MHz

Satellite Loop-Through loss: 3dB

Terrestrial Loop-Through loss: 3dB

Made in China

Designed in LU

Legacy Out

Unicable Out

TM

Satellite - loop-through output

+

V/HH/L H/HV/L

[+Terrestrial][+Terrestrial]

Produktspezifikationen