Jablotron JA-68 Bedienungsanleitung
Jablotron
Sicherheit
JA-68
Lies die bedienungsanleitung für Jablotron JA-68 (1 Seiten) kostenlos online; sie gehört zur Kategorie Sicherheit. Dieses Handbuch wurde von 22 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 11.5 Bewertungen. Hast du eine Frage zu Jablotron JA-68 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
JA-68 universal output module 2 / 2 MGK23701
The JA-68 universal output module
The JA-68 is a universal output module designed for use within Jablotron
systems of the JA-80 OASiS, JA-63 Profi and JA-65 Maestro series. The
module provides eight factory pre-programmed semiconductor outputs and a
switch-over relay output. The relay can be configured using 10 DIP switches
which allows for multiple function assignment. There is no limit in the number
of JA-68 modules used in the system. There is no limit to the number of
JA-68 modules used in the system and the JA-68 module can be combined
with GSM, LAN or PSTN (landline) communicators.
The module is designed for being placed into the control panel
housing.
NC
C
NO
Figure 1
Semiconductor outputs
All semiconductor outputs are switchable to a common terminal labelled
“C”. The switching ON/OFF logic can be reversed by setting a jumper JP1 to
the NC position (the factory default is NO).
Description of the terminals:
Terminal Function
+U Positive power supply from the digital bus (limited to 200 mA)
GND Negative pole of the power supply
C Common terminal (for all semiconductor outputs)
ARM Anything-set status (A or AB or ABC)
ALM Intruder alarm
FIR Fire alarm
TMP Tamper alarm
PNC Panic alarm
FLT Fault indication (general faults, radio communication faults,
back-up battery supply faults)
AC Mains (230V) supply fault
LB Low battery indication (applies to wireless devices such as
detectors, keypads, sirens or thermostats)
Relay configuration
The relay is configurable via a set of 10 DIP switches (see Table 2). The
relay works with OR logic: it is switched ON if there is at least one preset
function activated.
Example: Setting switches 2,3,4 and 5 to ON causes the relay to
indicate intrusion, fire, tamper or panic alarms i.e. the relay switches ON if
any of the four mentioned alarm states are activated.
DIP switches assignments:
Number Label Function
1 ARM Anything set
2 ALM Intrusion alarm
3 FIR Fire alarm
4 TMP Tamper alarm
5 PNC Panic alarm
6 FLT System fault
7 AC Power supply fault
8 LB Low battery
9 PGX Control panel PGX output
10 PGY Control panel PGY output
Description of relay terminals:
Label Description
NC Normally Closed relay contact
C Common relay contact
NO Normally Open relay contact
Note: There is a minimum output activation time of 10 seconds for each
of the 8 + 1 outputs.
Specification
Power supply 12V (taken from the control panel)
Stand-by consumption 4mA
Maximum consumption (all outputs activated) 50mA
Outputs 8 semiconductor switches
+ 1 switch-over relay
Maximum current for single output activation 200mA
Maximum current for C, NC or NO activation 1A / 60V
Minimum output activation time 10 sec.
Digital bus connection 2x RJ-44 data connectors
Environment indoor general
Operational temperature range –10 to +40 °C
Complies with EN 50130-4,EN 55022
JABLOTRON ALARMS a.s. hereby declares that the JA-68
is in compliance with the essential requirements and other
relevant provisions of Directive 2004/108/EC. The original of
the conformity assessment can be found on the web site
www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the manufacturer after use.
Produktspezifikationen
| Marke: | Jablotron |
| Kategorie: | Sicherheit |
| Modell: | JA-68 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Jablotron JA-68 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sicherheit Jablotron
23 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
20 August 2024
18 August 2024
18 August 2024
Bedienungsanleitung Sicherheit
- Panasonic
- Honeywell
- Optex
- Devolo
- Sygonix
- Epine
- Xena
- Basetech
- Nest
- EasyMaxx
- Foscam
- SecuFirst
- Batavia
- Velleman
- Golmar
Neueste Bedienungsanleitung für -Kategorien-
5 Oktober 2024
24 September 2024
20 September 2024
19 September 2024
17 September 2024
17 September 2024
16 September 2024
16 September 2024
27 August 2024
27 August 2024