JBL BassPro Nano Bedienungsanleitung

JBL Subwoofer BassPro Nano

Lies die bedienungsanleitung für JBL BassPro Nano (3 Seiten) kostenlos online; sie gehört zur Kategorie Subwoofer. Dieses Handbuch wurde von 63 Personen als hilfreich bewertet und erhielt im Schnitt 3.9 Sterne aus 32 Bewertungen. Hast du eine Frage zu JBL BassPro Nano oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/3

Basspro Nano

Owner’s Manual

Basspro Nano

WIRING FOR POWER AND GROUND

Remote turn-on (blue) to

aftermarket stereo REM out

+12V (red)

Ground

(black)

Fuse holder, 15A fuse

Chassis ground (–) Battery

18” (46cm)

WIRING FOR AUDIO SIGNAL

Line-level from aftermarket stereo

Right line output

(from stereo)

Left line output

(from stereo)

NOTE: When connecting an aftermarket stereo to the BassPro

Nano’s line-level inputs and remote turn-on wire, set the

button to .

Speaker-level from factory or aftermarket stereo

Right + (from stereo)

Right – (from stereo)

Left – (from stereo)

Left + (from stereo)

Harness high-level input wire guide

White/White with black stripe Left + / Left -

Gray/Gray with black stripe Right + / Right -

ABOUT THE MANUAL

This manual displays general Owner’s Manual guideline. However,

please note that proper installation of mobile audio components

requires qualiﬁed experience. If you do not have the knowledge

and tools to successfully perform this installation, we strongly

recommend consulting an authorized JBL dealer about your

installation options. Keep all instructions and sales receipts for

reference.

WHAT’S IN THE BOX

2X 4X8X

MOUNTING THE BASSPRO NANO

Recommended location: under the passenger seat

NOTE: Before securing the BassPro Nano with mounting screws,

check beneath the mounting surface to ensure you will not

puncture fuel lines, brake lines, or any vehicle wires. Also ensure

that the BassPro Nano will not interfere with seat operation or

wiring, or block underseat heater/air conditioning vents.

Note: When connecting a factory or aftermarket stereo to the

BassPro Nano’s speaker-level inputs, set the

button to .

SETTING GAIN, ADJUSTING PHASE, LOW-

PASS FILTER, AND BASS BOOST

1. Start with control set to minimum, GAIN

and the crossover control rotated midway.

2. Choose music with substantial bass

content and turn the volume control on

your receiver to ¾ of its total output.

3. Adjust the control clockwise, GAIN

listening carefully to the bass output. If

you hear distortion, turn the control GAIN

counterclockwise to decrease the .GAIN

4. Switch the back and forth to PHASE

determine which setting provides the most

clean bass output.

5. Adjust the LOW-PASS FILTER control

until the BassPro Nano plays only low-

frequency information – you should not

hear elements such as vocals coming from

the woofer.

6. Adjust the control BASS-BOOST

clockwise or counterclockwise to suit your

taste.

CONNECTING THE REMOTE BASS

CONTROL MODULE

SPECIFICATIONS

• Driver Complement: 6” x 8” (152mm x 203mm) woofer

• Ampliﬁer Power Output: 100WRMS, 200W Max

• Frequency Response: 30 Hz – 150 Hz

• Fuse: 15A

• Maximum Current Draw: 13A

• Quiescent Current Draw: <600 mA

• Input Sensitivity: 0.1 V – 4.0 V low-level input; 0.25 V – 10V

high-level input

• Crossover Frequency: 50 Hz – 150 Hz

• Crossover Slope: 12 dB/octave

• Bass Boost: 0 dB to +12 dB @ 50Hz

• Dimensions (L x W x H): 10-1/4” x 7-11/16” x 2-15/16”

(260mm x 195mm x 74.6mm)

• Weight: 7.78lbs. (3.53kg)

TROUBLESHOOTING

No audio and indicator is offPOWER

• No voltage at BATT+ and/or terminals, or bad or no

ground connection. Check voltages at ampliﬁer terminals with

VOM.

No audio and indicator ashes every 4 seconds

• DC voltage on ampliﬁer output. Ampliﬁer may need service; see

enclosed warranty card for service information.

No audio and and indicators ash

• Voltage less than 9V on BATT+ connection. Check vehicle

charging system.

No audio and indicator is on

• Ampliﬁer is overheated. Make sure ampliﬁer cooling is not

blocked at mounting location. Or, there may be voltage greater

than 16V (or less than 8.5V) on connection. Check

vehicle charging system.

Amplier fuse keeps blowing

• The wiring is connected incorrectly or there is a short circuit.

Check wiring connections.

Distorted audio

• is not set properly. Check setting. Check wires for shorts

or grounds. Ampliﬁer or source unit may be defective.

Music lacks dynamics or “punch.”

• If using speaker-level inputs, check connections for proper

polarity. Switch back and forth between 0° and 180°

and leave on setting with best sound.

Engine noise—whining or clicking—in system when the

engine is on

• Ampliﬁer is picking up alternator noise. First, check ground

connection on the ampliﬁer – a loose or improper ground is

one of the main causes for noise. Turn down . Move RCA

audio cables away from power wires. Installing an alternator

noise ﬁlter on power line between battery and alternator might

also be necessary.

HARMAN International Industries,

Incorporated 8500 Balboa Boulevard,

Northridge, CA 91329 USA

www.jbl.com

JBL is a trademark of HARMAN International Industries, Incorporated,

registered in the United States and/or other countries. Features, speciﬁcations

and appearance are subject to change without notice.

Produktspezifikationen

Marke:	JBL
Kategorie:	Subwoofer
Modell:	BassPro Nano
Breite:	195 mm
Tiefe:	260 mm
Gewicht:	3530 g
Produkttyp:	Vorgeladener Subwoofer
Produktfarbe:	Schwarz
Höhe:	74.6 mm
Schnellstartübersicht:	Ja
Zertifizierung:	CE
Ein-/Ausschalter:	Ja
Subwoofer-Treiberdurchmesser (imperial):	6 "
RMS Leistungsoutput pro Kanal (4 Ohm):	200 W
Subwoofer-Typ:	Aktiver Subwoofer
Subwoofer Effektivwert Energie:	200 W
Subwoofer Frequenzbereich:	30 - 150 Hz
Subwoofer Empfindlichkeit:	12 dB
Subwoofer-Treiberdurchmesser:	152 mm
Subwoofer Übergangsfrequenzen:	50 - 150 Hz
Subwoofer-Lautsprechermembranmaterial:	Fiberglas