JBL Synthesis SDA4600 Bedienungsanleitung
Lies die bedienungsanleitung für JBL Synthesis SDA4600 (16 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 12 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 6.5 Bewertungen. Hast du eine Frage zu JBL Synthesis SDA4600 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/16
JBL SYNTHESIS®
SDA8300
SDA4600
AMPLIFIER
SYSTEM INSTALLATION GUIDE
May, 2014
P/N 070-90018 (rev A.0)
2 | J B L S y n t h e s i s S D A 8 3 0 0 / S D A 4 6 0 0 S y s t e m G u i d e
Read Me First!
IF YOU READ NOTHING ELSE IN THIS GUIDE READ THIS INFORMATION:
The SDA ampliers come pre-congured to work with the SDEC4500P using
the BLU-LINK digital audio signal over Cat5e Ethernet cables. The ampliers
should not be connected to the home network. Analog Audio input comes
IN on the SDEC4500P (up to 12 channels) and OUT on the SDA8300 and/or
SDA4600 without going through any Digital to Analog conversions (up to 20
Channels as standard, expandable to 128 channels).
Two alternate conguraons are selected by using the included selecon
trigger that plugs into the GPIO input on the rear panel. These are labeled
“Conguraon 2” and “Conguraon 3” on the plug.
The SDA8300 amplier ships congured for a simple 7-channel system. The
SDA8300 can access two (2) addional conguraons. Using combinaons
of these conguraons allows the system to output from a simple 7 x 300
Wa system to up to 16 x 300 Was with discrete DSP for each channel
with acve bi-amp outputs on the Le-Center-Right.
The SDA4600 ships congured for a 4-channel subwoofer (4 x 600 Was).
Up to two (2) addional conguraons can be accessed for bridged high
power subwoofers outputs (2 x 1200 Was with discrete channel DSP for )
each output. These are used with the Harman Patented “Sound Field
Management” in the SDEC4500P.
The controls all DSP and -AMP speaker crossover sengs and SDEC-4500P BI
must be congured with either “JBL Synthesis ARCOS” soware or “SDEC
Control Panel Soware v1.5 Go to ”. www.jblsynthesis.com to download the
correct soware.
The ONLY inputs into the SDA ampliers should be from the Cat5e cable
connected to the BLU-Link In/Out. Analog inputs are provided as a backup
only and is not recommended. DO NOT USE BOTH BLU-LINK AND ANALOG
AS UNEXPECTED RESULTS CAN OCCUR.
DO NOT CONNECT THE AMPLIFIER TO THE HOME NETWORK. THE NETWORK
CONNECTION IS FOR ADVANCED SETUP AND MONITORING. THERE ARE NO
USER CONTROLLABLE FUNCTIONS FROM THE NETWORK. ONLY THE BLU-
LINK SIGNAL CHAIN MUST BE CONNECTED USING STANDARD CAT5E
ETHERNET CABLES.
Step by Step Setup Guide. Detailed instrucons are on the next pages.
1. Connect Preamp/Surround Processor and SDEC4500P
2. Connect Blu-Link Digital Audio Link from SDEC4500P to SDA
Amplier(s) using standard Ethernet Cat5e cables
3. [Oponal] Connect Powered Subwoofers to SDEC4500P
4. Setup of SDA8300 for Single (8-channel) or Dual unit (16-
channel) conguraon and connect speakers
5. Setup of SDA4600 for Single (4-channel x 600 W) or Bridged
(2-Channel x 1200 W) or Bridged Dual unit conguraon and
connect subwoofers
Accessories
Power cords (North America and EU)
Rack screws
Analog input screw down connectors
Speaker Terminal crimp connectors
Rear Rack Rail support
Sleep trigger 3-conductor screw down connector
SDA4500XLRIC interconnect kit [PURCHASED SEPARATELY]
Auto Standby / Auto Turn On
The ampliers will go to low power standby if any channel does not receive
signal for more than 30 minutes. The individual Channel Ready light will
blink green in standby. This is on a PER CHANNEL basis. The amplier will
Auto Turn On when the signal returns above -60db in level and the Channel
Ready light will stay solid green.
Sleep Mode
This is a CONTACT CLOSURE. Only use with dry contact closure from control
systems. The amplier can be put to sleep by connecng pins 1 and 2 on the
AUX port. When applying this connecon, the amplier will shut down and
remain in sleep unl the connecon between pins 1 and 2 is open. While
the amplier is in sleep, the front panel power buon is disabled. When the
connecon between pins 1 and 2 is open, the amplier will revert to its last
conguraon and begin to output audio within 20 seconds.
3 | J B L S y n t h e s i s S D A 8 3 0 0 / S D A 4 6 0 0 S y s t e m G u i d e
Standard System [i.e., Syn-2-Array / Syn-3-Array / Syn-4 / or Similar]
Typical STANDARD system conguraon. Factory Defaults. DO NOT
INSERT THE CONFIGURATION JUMPERS. Standard systems support 7.4
with the to acve bi-amplify the Center Channel. opon
Expanded Systems [i.e., Syn-Everest / Syn-K2 / Syn-Atlas / Syn-1-Array]
Fully expanded system using Conguraon 2 and Conguraon 3 for 13.4
Channel system. Front Le-Center-Right have the opon to be bi-wired or
acvely bi-amplied.
Conguraon 2
Conguraon 2
Conguraon 3
Conguraon 3
Cong aon
Cong aon
SDA8300 #1
SDA8300 #2
SDA4600 #1
SDA4600 #2
SDA8300 #1
SDA4600 #1
SDEC-4500P
SDP PREAMP
SDEC-4500P
SDP PREAMP
Produktspezifikationen
| Marke: | JBL |
| Kategorie: | Empfänger |
| Modell: | Synthesis SDA4600 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JBL Synthesis SDA4600 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger JBL
27 September 2024
4 September 2024
4 September 2024
31 August 2024
27 August 2024
12 August 2024
8 August 2024
31 Juli 2024
29 Juli 2024
29 Juli 2024
Bedienungsanleitung Empfänger
- Ashly
- Vision
- Neumann
- Kali Audio
- Polsen
- Edwards Signaling
- Koda
- Clarion
- HQ Power
- Monacor
- AVM
- Jamo
- Jolida
- Rupert Neve Designs
- Majestic
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025