JennAir JJW3430LM Bedienungsanleitung
Lies die bedienungsanleitung für JennAir JJW3430LM (80 Seiten) kostenlos online; sie gehört zur Kategorie Ofen. Dieses Handbuch wurde von 13 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 7 Bewertungen. Hast du eine Frage zu JennAir JJW3430LM oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/80
FOR SERVICE TECHNICIAN’S USE ONLY
Tech Manual Do not remove or destroy
W11324892A 08/20
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.
DANGER
Electrical Shock Hazard
Only authorized technicians should
perform diagnostic voltage measurements.
After performing voltage measurements,
disconnect power before servicing.
Failure to follow these instructions can
result in death or electrical shock.
Voltage Measurement Safety Information
When performing live voltage measurements, you must do the following:
■ Verify the controls are in the off position so that the appliance does not start when energized.
■ Allow enough space to perform the voltage measurements without obstructions.
■ Keep other people a safe distance away from the appliance to prevent potential injury.
■ Always use the proper testing equipment.
■ After voltage measurements, always disconnect power before servicing.
FOR SERVICE TECHNICIAN’S USE ONLY
2
IMPORTANT: Electrostatic Discharge (ESD) Sensitive Electronics
ESD problems are present erywhere ESD may damage or weaken the electronic control assemblyev . . The new control
assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.
■ Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the
appliance
-OR-
Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.
■ Before removing the part from its package, touch the antistatic bag to a green ground connection point or
unpainted metal in the appliance.
■ Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.
■ When repackaging failed electronic control assembly in antistatic bag, observe above instructions.
3
Diagnostics
Unplug oven or disconnect power before performing the following checks:
■A potential cause of a control not functioning is corrosion on connections.
Observe connections and check for continuity with an ohmmeter.
■All tests/checks should be made with a VOM or DVM having a sensitivity
of 20,000 Ω per volt DC or greater.
■Check all connections before replacing components, looking for broken or
loose wires, failed terminals, or wires not pressed into connectors far enough.
Damaged harness must be entirely replaced. Do not rework a harness.
■Resistance checks must be made with power cord unplugged from outlet
and with wiring harness or connectors disconnected.
■If the oven does not heat, there may be a problem with connections to
the power supply. Check the connection to L2.
IMPORTANT: Do not replace the control if there is no evidence of any failure.
To Enter Diagnostics Mode:
Before proceeding with any corrective action, perform the following steps to
enter the Diagnostics mode:
1. Enter Diagnostics mode by pressing the same 3 keypads 3 times in a row.
Single Ovens: Press KITCHEN TIMER>TOOLS> SELF CLEAN (Repeat 2
more times.)
Double Ovens: Press UPPER OVEN>LOWER OVEN>LOWER LIGHT
(Repeat 2 more times.)
NOTE: You do not need to wait for any audible or visual feedback from the
control between keypad presses.
2. If control does not enter Diagnostics mode, continue repeating the keypad
sequence from Step 1. All the keypads will light up when the control enters
Diagnostics mode.
3. From the Diagnostic menu, scroll to the desired selection using the touch
screen.
Error Diagnostics: View and clear the failure history.
Component Activation: Manually activate each relay.
Sensors & Switches: View the traditional oven cavity temperatures and
door/latch switch status.
System Information: View the model number, serial number, and
software versions.
Wi-Fi: View Wi-Fi related content such as IP Address, Gateway, SSID,
and connection status.
Exit Diagnostics
General Procedure: Error Codes
NOTE: All failures are stored in the failure history. To check if the error code
is still present, start a cooking function and wait 1 minute to check if the error
appears.
1. Enter Diagnostics mode.
2. Touch or scroll to “Error Diagnostics” in the Diagnostics menu, and then
touch “OK.”
3. To clear error codes, touch “Clear History.”
4. If no failures are listed, the message “No Error” will appear on the screen.
General Procedure: Software Version
For Engineering only
Produktspezifikationen
| Marke: | JennAir |
| Kategorie: | Ofen |
| Modell: | JJW3430LM |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JennAir JJW3430LM benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Ofen JennAir
2 September 2024
21 August 2024
20 August 2024
20 August 2024
20 August 2024
18 August 2024
18 August 2024
17 August 2024
17 August 2024
16 August 2024
Bedienungsanleitung Ofen
- Heidenfeld
- Bellini
- Daewoo
- Prima
- Unox
- Logik
- Zelmer
- Miele
- Backyard Pro
- Cadac
- Winia
- MX Onda
- ZLine
- Ufesa
- Baumatic
Neueste Bedienungsanleitung für -Kategorien-
19 Juni 2025
19 Juni 2025
18 Juni 2025
18 Juni 2025
16 Juni 2025
10 Juni 2025
9 Juni 2025
8 Juni 2025
6 Juni 2025