Jensen BUCAM300AJ Bedienungsanleitung
Jensen
Nicht kategorisiert
BUCAM300AJ
Lies die bedienungsanleitung für Jensen BUCAM300AJ (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 58 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 29.5 Bewertungen. Hast du eine Frage zu Jensen BUCAM300AJ oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Mounting the camera
Look for a locaon that will give you the best view behind the vehicle.This should not be
directly next to or under a reverse/backup lamp as it may blind the camera at night.Avoid
license plate lamps as well as they may blind the camera at night. Before drilling,
determine the best way to run the power wires to the reverse lights & the extension cable
through the car.Insure that your route will not interfere with any safety equipment,trunk
release or other items in the vehicle.Look for wires, sensors,double metal,anything that
could cause a problem or damage.The camera should lay flat against the mounng surface
for proper installaon.
1.Use the included hardware to secure the camera to the vehicle.DO NOT OVERTIGHTEN the hardware.
2.Follow ONE of the following wiring opons.
Oprion 1: Connect camera power wire to the vehicle's reverse lamp:
a)Locate the reverse lamp in the tail light assembly.
b)Aach the red wire to the posive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connecon
is secure. Once this connecon is complete,note that the red power wire that is located on either end of the video RCA cable will not
be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potenal power interrupon.
c)Aach the black wire to ground(-).
d)Run video cable to the locaon of the receiver or monor(not included).Connect one yellow RCA end of the video cable to the
camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).
e)Run audio cable to the locaon of the receiver or monor(not included).Connect one black RCA end of the audio cable to the
camera and connect the other end of the back RCA cable to the audio source(receiver/monitor).
Opon 2: Connect camera power wire to receiver/monitor power:
a)From camera locaon,connect red power wire from power cable to red power wire from one end of the video cable.Use a crimp
connector or soldering tool to ensure connecon is secure.
b)Aach the black wire to ground.
c)Run video cable to the locaon of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the
camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).
d)From video source(receiver/monitor) locaon,connect red power wire from end of the video cable to the reverse wire lead located
on the video source(receiver/monitor).
e)Run audio cable to the locaon of the receiver or monitor(not included).Connect not black RCA end of the audio cable to the camera
and connect the other end of the black RCA cable to the audio source(receiver/monitor).
Camera Specifications
Image Sensor: CMOS,7440H
Power: 12V DC,Negave Ground
Power Consumpon: 1 Wa＜
Effecve Pixels: 733H × 493V
Video Format: NTSC
Lux: 0.5＜
White Balance: Auto
Viewing Angle: 170 Degrees
IP Rang: IP67
Operang Temperature: -30 ~ +70℃ ℃
Camera Body: Zinc Alloy
Microphone Specifications
Audio input
of receiver
Camera input
of receiver
1.6 Ft.
Sensivity: -30±2 dB
Amplifying Power: 0.2 W
S/N Rao(A weighted network): 70(Min) dB
Direconal Characterisc Omni-Direconal：
Maximum Input Sound Pressure Level: 100 dB
Waterproof Rang: IP67
Produktspezifikationen
| Marke: | Jensen |
| Kategorie: | Nicht kategorisiert |
| Modell: | BUCAM300AJ |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Jensen BUCAM300AJ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Jensen
7 Juli 2025
9 Oktober 2024
22 September 2024
21 September 2024
28 August 2024
6 August 2024
2 August 2024
27 Juli 2024
22 Juli 2024
21 Juli 2024
Bedienungsanleitung Nicht kategorisiert
- Intermatic
- Neutrik
- VirtuFit
- EZ Dupe
- Easypix
- Pfaff
- Novy
- Expressive E
- Motu
- HN-Power
- Olivetti
- Edesa
- Alfen
- EmberGlo
- Mooer
Neueste Bedienungsanleitung für -Kategorien-
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025