Jensen XDA95RB Bedienungsanleitung
Lies die bedienungsanleitung für Jensen XDA95RB (10 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 2 Bewertungen. Hast du eine Frage zu Jensen XDA95RB oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/10
NSA1124-V01
2025
XDA91RB,92RB,94RB,95RB
XDA SERIES
Preparation
Please read entire manual before installation. Due to the technical nature
of ampliers, it is highly recommended that your amplier is installed by a
professional installer or an authorized dealer.
Before You Start
• Disconnect negative battery terminal. (consult a qualied technician for
instructions)
• Avoid installing the amplier where it would be subject to high temperatures, such
as from direct sunlight, or where it would be subject to dust, dirt or excessive
vibration.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• All amplier installations require power, signal and speaker wires (not included).
• An amplier installation kit (sold separately) is highly recommended to facilitate
the installation. Consult your dealer for recommendations.
Mounting Location
• Choose a mounting location for the amplier. Suggested locations include under a
seat or in the trunk.
• The amplier can be mounted horizontal (recommended) or vertical. For optimum
performance, make sure to provide at least 1" of space around all sides. Do not
mount the amplier under carpets or where airow is restricted.
• Do not install the amplier where it may be exposed to moisture.
• The optimum mounting location varies between vehicles. Remember to test all
amplier functions before completing the nal mounting procedure.
TYPICAL
MOUNTING
METHOD
1
XDA SERIES
18
0
XDA SERIES
NOTE:
Be sure to follow specic instructions included with your amplier installation kit
(not included with this amplier). The information below should be used as a general
guideline only.
Power Wire (+12V)
• Disconnect negative battery terminal before proceeding. Consult a qualied
technician for instructions if you are unsure.
• Plan wire routing before cutting any wires to length. Begin by routing the power
+12V wire from the battery to the amplier location. Use a grommet when running
wires through the rewall or metal openings. Avoid running the power wire near
existing vehicle wiring to prevent induced noise from entering the audio system.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s
electrical system.
Ground Wire (GND)
• The amplier ground wire should be as short as possible (no more than 36" or
1 meter). Choose a clean unpainted section of metal or the vehicle chassis when
attaching the ground connection. Be sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
• The remote turn-on wire connects to the head unit's amplier turn-on lead or
power antenna output.
Speaker Wires
• Choose adequate gauge speaker wire depending on your exact amplier/speaker
combination. Be sure to observe polarity when connecting.
• Do not ground any speaker wires or connect any speaker wires together.
Input Signal
• The amplier's input signal connects to the head unit's low level (RCA) or high level
(speaker wire) outputs.
• Low level input signals deliver the best performance. If unavailable, use the high
level inputs - when interfacing with factory head unit for instance.
Power / Protect Indicators
• Colored LED indicators illuminate from the plastic power terminal.
• The blue LED illuminates during normal operation (POWER) and the red
LED indicator is visible when the amplier detects a fault ( PROTECT).
CAUTION
• Do not use both low and high
level inputs at the same time. Connect only one or the
other.
• Keep low level inputs away from any power wires to avoid engine noise.
• Never run any wires underneath or outside the vehicle.
Connection Descriptions
2
Notes
XDA SERIES
17
Produktspezifikationen
| Marke: | Jensen |
| Kategorie: | Empfänger |
| Modell: | XDA95RB |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Jensen XDA95RB benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger Jensen
16 Juni 2025
2 Dezember 2024
12 September 2024
7 September 2024
28 August 2024
28 August 2024
6 August 2024
5 August 2024
4 August 2024
3 August 2024
Bedienungsanleitung Empfänger
- Omnitronic
- RCF
- LEA
- EMOS
- Topp Pro
- AmpliVox
- Mac Audio
- Optoma
- Dimavery
- Match
- Klipsch
- Black Lion Audio
- Solid State Logic
- Kemo
- Gold Note
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025