SB-H-RIDGLNE/10W3v3_ 011214
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 6
From under the vehicle, place the supplied fender washer,
flat washer, lock washer and then hex nut onto the protrud-
ing socket cup set screw. Secure tightly with a 14mm socket,
long extension and rachet.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
S T E P 5
(A) Loosen the socket cup set screw to expose 1-1/2-inch.
Place the enclosure into place, carefully guiding the socket
cup set screw through the drilled hole. .
(B) Run speaker wire from the amplifier location to the
Stealthbox® and attach to the terminal
Double check the woofer for proper operation.
S T E P 4
A Position the Stealthbox® into place and press firmly
down. This is to make an impression onto the wax square.
Remove the Stealthbox®.
B With a 1/2" drill bit or StepBit/Unibit® and drill. Drill at the
impression on the wax square, through the metal floor to the
outside.
(C) Remove the wax square.
Page 2 • JL Audio, Inc 2016
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011214 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
w w w . j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(1) 3/8-inch - 16 Hex Nut 3-inch x 3-inch Wax Square(1)
(1) 3/8-inch x 3/4-inch USS Flat Washer 3/8-inch - 16 x 2-1/4-inch Socket Cup Screw(1)
(1) 3/8-inch x 1-1/4-inch Fender Washer
(1) 3/8-inch Lock Washer
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W3v3-2
Nominal Impedance: 2 ohms
Continuous Power Handling: 500 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2. The diagram below shows
the recommended crossover settings for the XD300/1v2 when being used to power your Stealthbox ®.
The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5-inch / Front Doors
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650
C3-650, C5-650x, C5-650, & ZR650-CSi
Rear Speaker Size / Location: 6.5-inch / Rear Deck
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650
C3-650, C5-650x, C5-650, & ZR650-CSi