Joblotron TP-87 Bedienungsanleitung

Lies die bedienungsanleitung für Joblotron TP-87 (2 Seiten) kostenlos online; sie gehört zur Kategorie Sicherheitskamera. Dieses Handbuch wurde von 61 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 31 Bewertungen. Hast du eine Frage zu Joblotron TP-87 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

TP-87 programmable digital-bus thermostat 1 / 2 MKL52201

The TP-87 programmable digital-bus thermostat

The TP-87 is an indoor thermostat with a programmable weekly heating

schedule. It is designed to work exclusively in combination with

AC-8007 / AC-8014 devices. The thermostat provides indoor temperature

regulation which balances economy with comfort. The device is capable of

recognizing warm-up persistence characteristics (within 2 days) and will

adjust the settings accordingly so that a high level of operational comfort is

achieved. You need not find out how early the heating should start in order to

get to a comfortable temperature at the desired time. The required timing is

configured automatically.

Temperature adjustment can be performed by simply turning the setting

knob.

The following features are also available:

• Anti-freeze protection– any drop in temperature under the

(configurable) AL Lo value is detected and signalled to the receiver,

causing the receiver’s FRE output terminal to be activated.

• Floor temperature detection – the thermostat is equipped with an input

terminal for temperature sensor connection. This is especially suitable for

under-floor heating control – by placing the sensor directly into the floor

the heating regulation can be performed with higher precision.

When combined with an Oasis wireless security system (Jablotron), the

following are possible:

• Switching the heating ON and OFF remotely (by mobile phone, remote

control or Internet).

• Disabling the heating when windows are open.

• Informing the user about heating faults.

• Informing on the occurrence of fire (when the temperature is above a pre-

configured value).

Tab

Button

Installation

The TP-87 should be mounted in a dry indoor location. Choose a mounting

location about 1.5 meters above the floor in an area with good air circulation.

Avoid places with draughts, dead air spots and radiant heat from the sun or

appliances.

1. Release the upper cover by pressing the plastic tab on the bottom side of

the housing

2. Mount the back part on to the desired location.

3. Connect the receiver’s digital bus wires to the BUS terminals. The

polarity is irrelevant.

4. Should a floor sensor be used, wire it to the SEN terminals.

5. Close the thermostat.

6. Enroll the thermostat to the receiver by entering menu M1. The receiver

must be in enrollment mode (see the AC-8007/8014 manual).

Symbols on the display

Low battery

Heating ON

Time / temperature

displayManual mode

Time adjustment

Programming

Service menu

Week days

Comfort temperature

Economy temperature

Scheduled time display

Adjustment and programming

All the required parameters can be configured in the adjustment menu

using the knob. The menu is divided into the following parts:

M1 manual temperature-adjustment

M2 setting the economical or comfortable temperature, time

adjustment

M3 weekly programming schedule

M4 service menu

You can enter the menu and scroll through M1 to M4 by pressing and

holding the knob. The desired submenu is selected by releasing the knob.

Scrolling inside any particular menu M1 to M4 is done by turning the knob.

The currently displayed parameter can be adjusted by pressing the knob

briefly, turning the knob until the desired value is displayed, and confirming

the setting by re-pressing the knob (this will also cause a return to the menu

so that you can configure other parameters immediately). The adjustment

menu is escaped from by pressing the knob while OK is displayed or

automatically after approx. 30 seconds.

1. M1 – manual mode

If set to manual mode, the thermostat performs fixed

temperature regulation regardless of the weekly

schedule. The desired temperature can be set

within the range of t Lo to t Hi. The M1 menu is

escaped from by pressing and holding the knob for

2 seconds.

Note: As mentioned above, entering the M1 menu causes an enrollment

signal to be sent.

2. M2 – temperature & time setting

If the M2 menu is entered, turning the knob will scroll through the

Economical temperature (), Comfortable temperature () and Time ()

parameters followed by an OK option.

Mo

Each parameter can be entered by briefly pressing the knob. When or

is entered the displayed temperature flashes and can be adjusted by turning

the knob (re-pressing the knob confirms the setting). The Time parameter

adjustment is similar but requires three steps – for the day, hour and

minutes.

3. M3 – programming the weekly heating schedule

This mode allows you to program when the thermostat should switch

between Day () and Night () operation. The heating schedule can be

programmed either for each day separately or just for working days or just for

the weekend or for all days together.

PRG

SuM oTuWeThFrSa

PRG

SuSa

PRG

M oTuWeThFr

PRG

Mo

Enter the M3 menu, scroll to the desired option by turning the knob and

enter the schedule programming by briefly pressing the knob (this erases the

current schedule setting).

Mo

Mo

Mo

Schedule programming is done by marking

periods of time for which the Day heating

operation is requested. The marking bar is

shown at the bottom of the display, each hour

can be either marked or unmarked. You mark

or unmark by turning the knob. The

mark/unmark mode is displayed by /

symbols, the currently programmed hour is

shown on the display (00 to 23). Switching

between mark/unmark modes is done by

pressing the knob (this applies when turning

clockwise, turning the knob anti-clockwise

always switches to unmark mode).

Turning the knob to the rightmost position

(following hour 23) will display an OK option.

Pressing the knob will then finish programming.

4. M4 – Service menu

This menu allows for the configuration of parameters which usually stay

fixed during normal operation. When the service menu is entered, the

symbol is shown on the display. The menu contains 9 items (they can be

scrolled through by turning the knob). Each of the first 7 items corresponds to

a parameter which can be configured in a standard way (by pressing the

knob, turning the knob until the desired value is displayed, and re-pressing

the knob).

Produktspezifikationen