JUNG WS10H Bedienungsanleitung
JUNG
Nicht kategorisiert
WS10H
Lies die bedienungsanleitung für JUNG WS10H (5 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 13 Personen als hilfreich bewertet und erhielt im Schnitt 3.6 Sterne aus 7 Bewertungen. Hast du eine Frage zu JUNG WS10H oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/5
KNX Sensor and Transformer
Ref.-no.: WS 10 W, WS 10 HT, WS 10 R
Operating Instructions
Wind Sensor with Heating
Heating Transformer
Rain Sensor
c
1. Safety instructions
Attention: Electrical equipment must be installed and fitted by
qualified electricians only.
2. Wind Sensor Function
Wind sensor c serves for detecting and evaluating the wind velocity and
is provided for outdoor installation. It can be installed by means of the
attached mounting bracket.
Via a reed contact, the rotating speed is detected and converted into an
analogue output signal (0 ... 10 V).
An integrated heating (heating transformer option required) facilitates
operation during frost periods.
2.1. Wind Sensor Connection
Where:
1: white reference potential (earth)
2: brown 24 V DC operating voltage
3: green 0 .. 10 V + output
4: yellow 0 .. 10 V - output (earth)
5 + 6: grey / pink 24 V AC/DC heating transformer supply
Stand: Aug-08 325 061 13
KNX Sensor and Transformer
Ref.-no.: WS 10 W, WS 10 HT, WS 10 R
3. Rain Sensor Function
Rain sensor serves for detecting and evaluating the precipitation and
is provided for outdoor installation. It can be installed by means of the
attached 110° mounting bracket.
Via a meander and by utilising the conductivity of water, wetting by
precipitation is detected, evaluated and converted into an output signal
(dry = 0 V, rain = 10 V).
Intermediate values are not detected.
The output signal is reset only after the sensor surface has dried and
when an OFFdelay of 4 minutes has elapsed. The integrated heating
(additional heating transformer required as an accessory) accelerates the
drying process and melts ice and snow.
3.1. Rain Sensor Connection
Where:
1: white reference potential (earth)
2: brown 24 V DC operating voltage
3: green 0 .. 10 V + output
4 + 5: yellow/grey 24 V AC/DC heating transformer supply
4. Installation Instructions
• To supply the sensors (24 V DC) and to evaluate the sensor signals
an additional electronic device (e. g. the instabus weather station) is
required that can send measured value or command telegrams to the
instabus EIB, depending upon the analogue signals.
• Install the sensors in an accessible place to facilitate possibly
necessary cleaning.
• Do not install sensors in the vicinity of transmitting equipment (e. g.
mobile radio converters).
• Do not install sensor lines in parallel with lines carrying mains voltage
or loads.
To avoid electromagnetic irradiation keep a distance of a few
centimetres from such lines.
Note additionally for the wind sensor:
• Ensure correct positioning of the sensor (e. g. position not sheltered
from the wind).
Note additionally for the rain sensor:
• Do not damage the sensing surface and wipe with a mild cleaning
agent at a regular intervals.
• When installing the sensor, ensure unobstructed exposure to rain (do
not install under eaves).
2
KNX Sensor and Transformer
Ref.-no.: WS 10 W, WS 10 HT, WS 10 R
5. Heating Transformer Function
The heating transformer serves for the power supply of the heating
devices integrated into the rain sensors and wind sensors. Short-circuit
protection is implemented by means of an automatically resetting thermal
overload cut-out.
One rain sensor and one wind sensor, in each case, can be connected to
a heating transformer.
5.1. Heating Transformer Connection (Refer to Fig. )
UH1~: Sensor 1 connecting terminals.
UH2~: Sensor 2 connecting terminals.
Subject to technical modifications.
3
Produktspezifikationen
| Marke: | JUNG |
| Kategorie: | Nicht kategorisiert |
| Modell: | WS10H |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JUNG WS10H benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert JUNG
7 Oktober 2024
7 Oktober 2024
5 Oktober 2024
29 September 2024
22 September 2024
22 September 2024
20 September 2024
19 September 2024
19 September 2024
18 September 2024
Bedienungsanleitung Nicht kategorisiert
- Noctua
- Vent-A-Hood
- Bertazzoni
- Baumr-AG
- CRUX
- Industrial Music Electronics
- TTM
- Optoma
- Fujifilm
- BWT
- Sky-Watcher
- Thames & Kosmos
- Candy
- Max
- ProForm
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025