Kathrein VOS 43/RA-1G2 Bedienungsanleitung
Lies die bedienungsanleitung für Kathrein VOS 43/RA-1G2 (4 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 17 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 9 Bewertungen. Hast du eine Frage zu Kathrein VOS 43/RA-1G2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
1 / 4
VOS 43/RA-1G2 209500001
House connection amplifi er
Basic safety precautions
■House connection amplifi er for modern HFC networks up to
1,2 GHz
■Integrated high-effi ciency switched-mode power supply unit
■Power management: Unused amplifi er stage switch-off for
reduced power consumption
■Die-cast housing with F-type connectors
■Variable 6 dB interstage gain setting using on-board plug-in
attenuators (delivery condition: higher gain)
■The maximum operational levels also apply for operation with
interstage attenuation
■Interstage equaliser switchable with bridging plugs
(6 dB pre-emphasis)
■Integrated return path 5 – 204 MHz active/passive, off
(switchable with bridging plugs)
■Built-in variable attenuators (delivery condition return path:
max. attenuation) and variable equaliser
■LED to indicate operational mode
■Test socket on output -20 dB (with directional coupler)
■Test socket on input -20 dB (Return path 5 – 204 MHz)
■Test sockets are terminated with the EMK 03 in the delivery
status
■For indoor installation
■Conform to: EN 60728-11, EN 50083-2 und EN 32368-1
■The amplifi ers comply with the EMC directive 2014/30/EU and
Low-Voltage Directive 2014/35/EU applicable at the time of
shipping
►Installation must be carried out by authorised specialist staff .
►Unplug from the mains before installation.
►Described amplifi ers are exclusively for installation of HFC networks up to 1218 MHz.
►Any other use or failure to comply with these instructions will void the warranty or guarantee.
►The amplifi ers may only be installed in dry areas indoors. Do not install on or against highly combustible materials.
►The amplifi ers must be earthed when installed (Cu, minimally 4 mm2).
►The safety regulations set out in the current EN 60728-11 und EN 62368-1 standards must be complied with.
►The supply voltage of the amplifi ers is 230 VAC which can be fatal if touched directly!
►The only reliable method of disconnecting the amplifi ers from the mains is to unplug them.
►Do not touch live parts.
►The power plug must be easy to operate as the means of cutting power to the amplifi er, so the wall outlet must be
close to the amplifi er and easily accessible.
►The amplifi ers may only be installed and deinstalled in the voltage-free condition.
►Do not operate the amplifi ers without the factory-fi tted protective cover over the power supply unit. The cover must
be closed.
►No liquid-fi lled items may be placed on top of the amplifi ers.
►The amplifi ers are not to be exposed to dripping or splashing water.
►Ambient temperature range -20 bis +55 °C.
Merkmale
2 / 4
Setting of the amplifi er
To adjust the settings, a Phillips screwdriver is required to remove the housing cover.
The settings options are also imprinted on the housing cover.
Forward path Return path
① Pre-emphasis: 0 – 15 dB Pre-emphasis: 0 – 20 dB⑤
② ⑥ Attenuation: 0 – 20 dB Attenuation: 0 – 20 dB
③ ⑦ Interstage → Attenuation: 6 dB Attenuation: 0 dB | 10 dB
④ Interstage → Pre-emphasis: 6 dB A | B | C: Operation mode return path: (see graphic
and block diagram)
Optionally available accessories
Mounting
■De-emphasis equaliser: ERZ 120 (Order no. 272791)
■Lightning arrester: KAZ 12 (Order no. 21810002)
①
②
③ ④
⑤
⑥
⑦
A B C
active
passive
off
A B C
VOS 43/RA-1G2
30
30
118
44
50
Convection space
40
3 / 4
The following is required for installation:
■Fixings: screws, max. Ø 4.5 mm
■F-type connector plug as per EN 61169-24
Risk of damage to property!
An inner cable conductor with a diameter greater than
1.2 mm, or the presence of burrs may damage the device
inputs/outputs beyond repair.
Max. 2 mm
excess length
Clamping torque
max. 3.4 Nm
(danger of over-
winding)
Diameter
0.6 - 1.2 mm free of burrs
Block diagram
Connection example
VOS 43/RA-1G2
ESM 30
(ESM 40/G)
KAZ 12
EAX 26/G
EBC 04/G
0 – 20 dB
0 dB
6 dB
Pre-emphasis
Pre-emphasis Attenuation
5 – 204 MHz
258 – 1218 MHz
Preemphase
Input
5 – 1218 MHz
dB
dB dB
CBA
dB
Test 1
5 – 204 MHz
-20 dB
0 – 20 dB
5 – 204 MHz
258 – 1218 MHz
0 – 20 dB 0 – 15 dB
0 dB
6 dB
0 dB
10 dB
Output
5 – 1218 MHz
Test 2
5 – 1218 MHz
-20 dB
active
passive
off
A B C
230 V~
Attenuation
Attenuation Attenuation
Produktspezifikationen
| Marke: | Kathrein |
| Kategorie: | Empfänger |
| Modell: | VOS 43/RA-1G2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kathrein VOS 43/RA-1G2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger Kathrein
13 September 2024
30 August 2024
15 August 2024
14 August 2024
4 August 2024
26 Juli 2024
25 Juli 2024
24 Juli 2024
21 Juli 2024
19 Juli 2024
Bedienungsanleitung Empfänger
- GigaBlue
- Gira
- Auna
- JL Audio
- EA
- Soundtrack
- Mac Audio
- DirecTV
- Grundig
- Metronic
- Rolls
- Blustream
- Sonos
- SVS
- Qtx
Neueste Bedienungsanleitung für -Kategorien-
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
20 Juni 2025
20 Juni 2025