Kemppi A7 MIG Welder 450 Bedienungsanleitung
Kemppi
Schweißgerät
A7 MIG Welder 450
Lies die bedienungsanleitung für Kemppi A7 MIG Welder 450 (66 Seiten) kostenlos online; sie gehört zur Kategorie Schweißgerät. Dieses Handbuch wurde von 17 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 9 Bewertungen. Hast du eine Frage zu Kemppi A7 MIG Welder 450 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/66
350, 450
1920310
1804
A7 MIG WelderA7 MIG Welder
EN
INTEGRATION GUIDE
2A7 MIG Welder© Kemppi Oy 2018 1804
CONTENTS
1. Introduction ..........................................................................................4
2. Integration step by step ...................................................................4
3. Hardware installation ........................................................................5
3.1 Procedures before use ..............................................................................5
3.2 System overview .......................................................................................5
3.3 Power source .............................................................................................7
3.4 Cooling unit ...............................................................................................7
3.5 Wire feeder ................................................................................................7
3.6 Welding torch ............................................................................................9
3.6.1 Mounting .............................................................................................. 9
3.6.2 Push-pull torches ....................................................................................9
3.6.3 Wire inch button ....................................................................................9
3.6.4 Torch-cleaning with compressed air ...........................................................9
3.6.5 Touch-sensing with the gas nozzle ...........................................................10
3.7 Collision sensor .......................................................................................10
3.8 Interconnection cable set .......................................................................11
3.8.1 The arc measurement cable ....................................................................11
3.8.2 Wire feeder control cable .......................................................................12
3.8.3 Welding cable ......................................................................................12
3.8.4 Shielding gas hose ................................................................................12
3.8.5 Cooling hoses ......................................................................................12
3.9 Fieldbus communication ........................................................................13
3.10 Ethernet (web user interface server) ......................................................14
3.11 Emergency input functions ....................................................................14
3.12 Touch sensor status fast output ..............................................................15
3.13 I/O device ................................................................................................16
3.13.1 Installation ..........................................................................................16
3.13.2 Inputs ................................................................................................19
3.13.3 Outputs ..............................................................................................20
3.14 Dual wire feeder support ........................................................................21
3.14.1 Installation ..........................................................................................22
3.14.2 Connect the second wire feeder ..............................................................24
3.15 Powering up ............................................................................................24
4. Accessing the Web user interface ..............................................25
4.1 Conguring the network settings ..........................................................25
4.2 Opening the web user interface ............................................................26
5. System configuration ......................................................................27
5.1 Welding system, sensors and devices ....................................................27
5.1.1 General settings ...................................................................................27
5.1.2 Wire feed settings .................................................................................27
5.1.3 Gas sensor settings ...............................................................................28
5.1.4 General robot settings ...........................................................................29
5.1.5 Touch sensor settings ............................................................................29
5.1.6 Collision sensor settings ........................................................................29
5.1.7 Emergency stop settings ........................................................................29
5.1.8 Watchdog settings ................................................................................30
5.1.9 Welding system time .............................................................................30
5.2 Digital robot interface .............................................................................31
5.2.1 Fieldbus settings ..................................................................................31
5.2.2 Selecting the proper I/O table .................................................................31
5.2.3 Setting up scaling values .......................................................................32
5.3 Users ........................................................................................................34
5.4 Inputs and outputs ..................................................................................35
5.4.1 Inputs ................................................................................................35
5.4.2 Outputs ..............................................................................................35
5.5 Memory channels ....................................................................................36
5.6 System backup ........................................................................................36
6. Digital robot interface .....................................................................37
6.1 Control functions ....................................................................................37
6.1.1 WireFeedSpeed ....................................................................................38
6.1.2 Voltage ...............................................................................................38
6.1.3 FineTuning ..........................................................................................39
6.1.4 Dynamics ............................................................................................39
6.1.5 MemoryChannel ..................................................................................39
INTEGRATION GUIDE
3A7 MIG Welder© Kemppi Oy 2018 1804
6.1.6 PulseCurrent ........................................................................................40
6.1.7 PulseBaseCurrent .................................................................................40
6.1.8 PulseFrequency ....................................................................................40
6.1.9 PulseLength ........................................................................................40
6.1.10 WeldingAllowed ...................................................................................40
6.1.11 SimulationMode...................................................................................40
6.1.12 StartWelding .......................................................................................41
6.1.13 WireInch .............................................................................................41
6.1.14 WireRetract .........................................................................................41
6.1.15 GasBlow .............................................................................................41
6.1.16 AirBlow ...............................................................................................41
6.1.17 TouchSensorToolS el ..............................................................................41
6.1.18 TouchSensorOn ....................................................................................41
6.1.19 OnlineControl ......................................................................................41
6.1.20 Watchdog ...........................................................................................42
6.1.21 ErrorReset ...........................................................................................42
6.1.22 HotStartOn ..........................................................................................42
6.1.23 CraterFillOn .........................................................................................42
6.1.24 DigitalOutput1 – DigitalOutput8 .............................................................42
6.1.25 WireFeederSelect .................................................................................42
6.2 Status functions .......................................................................................43
6.2.1 WeldingCurrent....................................................................................46
6.2.2 WeldingVoltage ...................................................................................46
6.2.3 WeldingWireFeedSpeed.........................................................................46
6.2.4 MotorCurrent ......................................................................................46
6.2.5 GasFlowRate ........................................................................................46
6.2.6 ErrorNumber .......................................................................................46
6.2.7 WeldingMemoryChannel .......................................................................47
6.2.8 TAST ..................................................................................................47
6.2.9 WeldingProcess ....................................................................................47
6.2.10 Ready .................................................................................................47
6.2.11 PowerSourceReady ...............................................................................47
6.2.12 CoolingUnitOk .....................................................................................47
6.2.13 ProgramSaved .....................................................................................47
6.2.14 RobotHasControl ..................................................................................47
6.2.15 CycleOn ..............................................................................................47
6.2.16 ArcOn .................................................................................................48
6.2.17 GasFlowOk ..........................................................................................48
6.2.18 MainCurrentOn ....................................................................................48
6.2.19 CurrentOk ...........................................................................................48
6.2.20 MotorCurrentOk ...................................................................................48
6.2.21 WFSpeedOk ........................................................................................48
6.2.22 TouchSensed .......................................................................................48
6.2.23 Error...................................................................................................48
6.2.24 CollisionDetected .................................................................................48
6.2.25 ToleranceError .....................................................................................49
6.2.26 WireStuck ...........................................................................................49
6.2.27 GateDoorOpen ....................................................................................49
6.2.28 DigitalInput1 – DigitalInput8 ..................................................................49
6.2.29 PanelLocked ........................................................................................49
6.2.30 LocalRemote .......................................................................................49
6.2.31 AutoManual ........................................................................................49
6.3 I/O tables .................................................................................................50
6.3.1 KEMPPI1: KempArc Pulse default table ......................................................50
6.3.2 KEMPPI2: KempArc Pulse customized table................................................50
6.3.3 KEMPPI3: KempArc Pulse customized table................................................51
6.3.4 KEMPPI4: A7 MIG Welder default table ......................................................52
6.3.5 KEMPPI5: A7 MIG Welder table for pulse process control ..............................53
6.3.6 CUST1: Customer-specic table ...............................................................54
6.3.7 CUST2: Customer-specic table ...............................................................54
6.3.8 CUST3: Customer-specic table ...............................................................55
6.3.9 CUST4: Customer-specic table ...............................................................55
6.3.10 CUST5: Customer-specic table ...............................................................56
6.4 Timing diagrams .....................................................................................57
6.4.1 Welding startup timing ..........................................................................57
6.4.2 Welding stop timing .............................................................................59
6.4.3 Memory channel change timing ..............................................................61
6.4.4 Online control timing ............................................................................62
6.4.5 Wire inch and retract timing ...................................................................63
6.4.6 Touch sensor timing ..............................................................................64
6.4.7 Emergency stop response timing ............................................................65
INTEGRATION GUIDE
Produktspezifikationen
| Marke: | Kemppi |
| Kategorie: | Schweißgerät |
| Modell: | A7 MIG Welder 450 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kemppi A7 MIG Welder 450 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schweißgerät Kemppi
5 Oktober 2024
23 September 2024
22 September 2024
22 September 2024
22 September 2024
20 September 2024
20 September 2024
17 September 2024
24 August 2024
23 August 2024
Bedienungsanleitung Schweißgerät
- Frilass
- Powerplus
- Weldkar
- Kibani
- GYS
- Lincoln Electric
- Topex
- Scheppach
- Parkside
- Güde
- UNIMIG
- Weller
- Hilti
- FERM
- Anova
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
1 Oktober 2024
17 September 2024