Kenwood KMC-36 Bedienungsanleitung
Lies die bedienungsanleitung für Kenwood KMC-36 (7 Seiten) kostenlos online; sie gehört zur Kategorie Radio. Dieses Handbuch wurde von 34 Personen als hilfreich bewertet und erhielt im Schnitt 3.8 Sterne aus 17.5 Bewertungen. Hast du eine Frage zu Kenwood KMC-36 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/7
Document Copyrights
Copyright 2006 by Kenwood Corporation. All rights reserved.
No part of this manual may be reproduced, translated, distributed, or transmitted in any
form or by any means, electronic, mechanical, photocopying, recording, or otherwise, for
any purpose without the prior written permission of Kenwood.
Disclaimer
While every precaution has been taken in the preparation of this manual, Kenwood
assumes no responsibility for errors or omissions. Neither is any liability assumed for
damages resulting from the use of the information contained herein. Kenwood reserves
the right to make changes to any products herein at any time for improvement purposes.
© 2004-7 PRINTED IN JAPAN
B51-8697-00 (N) 1309
MICROPHONE / KEYPAD MICROPHONE
KMC-35/36
SERVICE MANUAL
1✽E30-7531-08 CURL CABLE
2 E58-0475-05 MODULAR JACK
3✽G01-4546-08 COIL SPRING (PTT)
4✽G53-1646-08 PACKING
5✽J19-5479-08 MIC HOLDER
6✽J19-5482-05 MIC HANGER (ACCESSORY)
7✽K29-9333-08 LEVER KNOB (PTT)
8✽K29-9334-08 KNOB (PTT)
9✽K29-9335-08 KEY TOP KMC-36
A N52-3012-60 PAN HEAD TAPPING SCREW
10 ✽S70-0499-08 TACT SWITCH
11 T91-0538-05 MIC ELEMENT
New
parts
Ref. No. Parts No. Description Destination
KMC-35 (Y58-3740-20), KMC-36 (Y58-3750-20) ✽ : New parts
PARTS LIST
KMC-35
KMC-36
Lever knob (PTT)
(K29-9333-08) Curl cable
(E30-7531-08)
Lever knob (PTT)
(K29-9333-08) Curl cable
(E30-7531-08)
Key top
(K29-9335-08)
KMC-35/36
2
■ Main PCB removal
1. Remove the four screws, the rear case and all-round pack-
ing.
2. Lift the switch PCB and remove it from the front case.
( )q
q
Switch PCB
w
Main PCB
q
w
qw
DISASSEMBLY FOR REPAIR
3. Lift the upper part of the Main PCB using a pair of twee-
zers ( ) and remove the Main PCB.w
■ Main PCB installation procedure
1. Install the microphone holder, spacer and keytop (KMC-36
only) on the front case.
2. Tilt the Main PCB and fit the modular connector into the
front case first.
3. Hold the modular connector with your fingers and move it
in the direction indicated by the arrow to install the Main
PCB onto the front case.
■ PTT knob installation procedure
1. Place the PTT knob in the front case diagonally as shown
in the figure.
2. Hold down the upper part of the PTT knob ( ) and pushq
the PTT knob shaft down ( ) to install the PTT knob ontow
the front case.
■ Hot microphone modification procedure
1. Lift the jumper with a pair of tweezers or similar tool. ( q)
Note : The jumper is bonded to the board, but not strongly
fixed, so it can be detached by applying light force.
2. Cut the base of the jumper into two parts with a pair of
nippers or similar tool. ( w)
Produktspezifikationen
| Marke: | Kenwood |
| Kategorie: | Radio |
| Modell: | KMC-36 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kenwood KMC-36 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Radio Kenwood
17 August 2024
14 August 2024
13 August 2024
13 August 2024
11 August 2024
4 August 2024
31 Juli 2024
27 Juli 2024
27 Juli 2024
26 Juli 2024
Bedienungsanleitung Radio
- Clas Ohlson
- Soundmaster
- Kathrein
- Stanley
- Data-Tronix
- Telefunken
- OK
- Bigben
- NGS
- Wolfgang
- JGC
- Lenoxx
- DigiTech
- Mtx Audio
- Infinity
Neueste Bedienungsanleitung für -Kategorien-
20 Juni 2025
20 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025