Kenwood KNA-SPM100 Bedienungsanleitung
Kenwood
Nicht kategorisiert
KNA-SPM100
Lies die bedienungsanleitung für Kenwood KNA-SPM100 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 15 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 8 Bewertungen. Hast du eine Frage zu Kenwood KNA-SPM100 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
KNA-SPM100
Speed Pulse Generator for KENWOOD Wireless Apple CarPlay Ready Receivers
KNA-SPM100 OBD-II Speed Pulse Generator
The KNA-SPM100 provides a simplified method for obtaining a vehicle’s speed pulse
information. It requests a vehicle’s speed using OBD-II and then generates a speed pulse
to be provided to the receiver.
◊ Compatible with most vehicles 2008 - Present
◊ Pre-programmed to work once installed
◊ Small footprint for easy installation
◊ Simple 3-wire hookup and OBD-II connection cable
◊ Red Wire - Connect to 12V Switched
Power
◊ Black Wire - Connect to Ground
◊ Purple/ Wire - Connect to
Receiver’s Speed Sense WirePink
◊ OBD-II Plug - Connect to Vehicle’s
OBD-II Plug
◊ Molex Plugs - Connect all to
KNA-SPM100 Interface
1. Power Receiver On.
2. The KNA-SPM100 interface LED will
blink 2 times, then OFF. RED
3. The KNA-SPM100 has successfully
programmed and is ready for use.
Connections Installation Instructions
If the KNA-SPM100 interface
did not blink 2 times, then RED
OFF, please refer to page 2.
White
KNA-SPM100
FAQ & Troubleshooting
LED Diagnostics FAQ
Receiver Messages
◊ LED Blinks IndenitelyRED
» KNA-SPM100 did not receive a
response from the vehicle.
- This means that the KNA-SPM100
is not compatible with that vehicle.
»CAN wires are disconnected.
- Verify CAN wire connections.
How can I verify if a vehicle is compatible?
» Verify that the vehicle’s year of
production is 2008+ and has an OBD-II plug.
»The KNA-SPM100 will not work If the
vehicle doesn’t allow a scan tool to be
plugged into it while the vehicle is turned
on and/or while driving. Vehicle’s that
may exhibit this symptom typically include
high-end European models.
»Ultimately, the only other way to verify if
the KNA-SPM100 is compatible is to connect
it to a vehicle and verify the LED sequence.
◊ LED Blinks / During that RED GREEN
Ignition Cycle
»KNA-SPM100 has detected another
OBD-II device, MRR, or another
radio replacement interface module
communicating on the bus.
- The KNA-SPM100 cannot be
used in conjunction with another OBD-II
device or MRR (please refer to the MRR or
radio replacement interface instructions
for vehicle speed pulse connection).
If you are still receiving a message like
this when attempting to use Wireless
Apple CarPlay while the vehicle is in
motion:
- The receiver is not receiving a proper
and/or any vehicle speed information.
- The GPS antenna is not connected
or an incorrect GPS antenna is being used.
Produktspezifikationen
| Marke: | Kenwood |
| Kategorie: | Nicht kategorisiert |
| Modell: | KNA-SPM100 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kenwood KNA-SPM100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Kenwood
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
30 Mai 2025
Bedienungsanleitung Nicht kategorisiert
- Xunzel
- CubuSynth
- Kiloview
- Boso
- RAVPower
- Wibrain
- Dreambaby
- Neo
- Massoth
- RF Elements
- UPO
- Esotec
- Carcomm
- Mamiya
- Unitech
Neueste Bedienungsanleitung für -Kategorien-
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025
20 Juni 2025