Kenwood NXR-810 Bedienungsanleitung

Lies die bedienungsanleitung für Kenwood NXR-810 (15 Seiten) kostenlos online; sie gehört zur Kategorie Funkkommunikation. Dieses Handbuch wurde von 35 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 18 Bewertungen. Hast du eine Frage zu Kenwood NXR-810 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

1

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment.

◆Refer service to qualified technicians only.

◆This repeater is intended for use as a fixed base station with

the antenna located outdoors on the rooftop or on an antenna

tower.

◆This repeater is designed for a 13.2 V DC power source!

Never use a 24 V DC or higher source to power the repeater.

◆Use only the supplied DC cord.

◆Do not remove the ferrite core attached to the DC cord. Doing

so may cause interference with radio communications.

THANK YOU!

We are grateful you purchased this repeater. We KENWOOD

believe this easy-to-program repeater will be highly effective in

your communications system, and will keep personnel operating

at peak efficiency.

PRECAUTIONS

• Donotexposetheunittorainormoisture;topreventreor

electric shock.

• Donotopentheunitunderanycircumstances;toavoidrisk

of electric shock.

• Donotexposetheunittolongperiodsofdirectsunlight,nor

place it close to heating appliances.

• Donotplacetheunitinexcessivelydustyand/orhumid

areas, nor on unstable surfaces.

• Ifyoudetectanabnormalodororsmokecomingfromthe

unit, disconnect the power from the unit immediately. Contact

your KENWOODservice center or dealer.

NOTICES TO THE USER

UNPACKING AND CHECKING EQUIPMENT

Note: The following unpacking information is for use by your

KENWOOD dealer, an authorized service center, or the KENWOOD

factory.

Carefully unpack the repeater. We recommend that you identify

the items listed in the following table before discarding the

packing material. If any items are missing or have been damaged

during shipment, file a claim with the carrier immediately.

ItemPart NumberQuantity

Hardware fixtureJ21-8559-XX1

Front glassB10-2635-XX1

Name platesB11-1259-XX1

CushionG13-1801-XX 4

CushionG13-1802-XX 4

FootJ02-0475-XX 2

FootJ02-0492-XX 2

GrommetJ59-0302-XX 2

HandleK01-0418-XX 1

ScrewsN30-4006-XX 2

ScrewsN35-3006-XX 5

DC cordE30-3427-XX1

Lead wire with connector (15 pin)E31-3228-XX1

FuseF05-1537-XX 1

Instruction ManualB62-2200-XX1

INSTALLATION

To install the handles onto the front panel of the repeater, align

the handles with the holes on the front panel, then secure the

handles using the supplied screws.

Please consult your dealer for installing the repeater and

antenna.

MICROPHONE

Connect an optional KMC-30, KMC-35, KMC-27A, KMC-27B,

KMC-9C, or KMC-53 microphone to the jack on KENWOOD MIC

the front panel.

NOTIFICATION

This equipment complies with the essential requirements of Directive

2014/53/EU.

RESTRICTIONS

This equipment requires a licence and is intended for use in the

countries as below.

ATBEDKFIFRDE GRISIE

ITLILUNLNOPTES SE CH

GB CYCZEEHUMTPLLVLT

SKSIBGHR TRRO

ISO3166

B62-2200-60 (E)

VHF DIGITAL BASE-REPEATER/ UHF DIGITAL BASE-REPEATER

INSTRUCTION MANUAL

NXR-710/ NXR-810

Information on Disposal of Old Electrical and Electronic Equipment and Batteries

(applicable for countries that have adopted separate waste collection systems)

Products and batteries with the symbol (crossed-out wheeled bin)

cannot be disposed as household waste.

Old electrical and electronic equipment and batteries should be

recycled at a facility capable of handling these items and their waste

byproducts.

Contact your local authority for details in locating a recycle facility

nearest to you.

Proper recycling and waste disposal will help conserve resources

whilst preventing detrimental effects on our health and the environment.

© 2019

The AMBE+2TM voice coding Technology embodied in this product

is protected by intellectual property rights including patent rights,

copyrights and trade secrets of Digital Voice Systems, Inc. This

voice coding Technology is licensed solely for use within this

Communications Equipment. The user of this Technology is explicitly

prohibited from attempting to extract, remove, decompile, reverse

engineer, or disassemble the Object Code, or in any other way

convert the Object Code into a human-readable form. U.S. Patent

Nos. #8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606,

and #8,359,197.

ModelFrequency rangeMax. output power

NXR-710-ETX/RX136.000 - 174.000 MHz50 W

NXR-810-ETX/RX400.000 - 470.000 MHz40 W

Firmware Copyrights

 ThetitletoandownershipofcopyrightsforrmwareembeddedinKENWOOD

productmemoriesarereservedforJVCKENWOODCorporation.

Produktspezifikationen