Kichler 15821CBR27 Short Lamp Bedienungsanleitung
Seiten 2 Lampen
Lies die Bedienungsanleitung für Kichler 15821CBR27 Short Lamp kostenlos online oder lade das PDF herunter. 32 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This xture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specications. Failure to adhere to
these codes and instructions may result in serious injury and/or property
damage and will void the warranty.
1) WARNING: This xture is not to be installed within 10 feet (3M) of a pool,
spa or fountain.
2) This xture is to be used only with a power unit (transformer) rated a
maximum of 300 W (25 AMPS) 15 volts.
3) The #18 ga. xture wire is not intended for direct burial.
4) Direct burial rated wire is to be buried a minimum of 6” (152mm) beneath
the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.
• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.
• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’
(76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’ (304 M), 15506-BK.
5) Fixture shall not use a tungsten halogen lamp unless the xture is marked
for use with such lamps.
6) Wiring connections must be made with approved/listed wire connection
device(s) suitable for the application. Do not exceed manufacturers’ wiring
combination specications for size and quantity of conductors.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),
CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT
BULB, LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for mounting xture.
2) At desired location, hammer stake (A) into ground. To avoid damage to
stake, place a board on top of stake while hammering. If ground is hard
and stake is difcult to install, make a crosscut in ground using a at shovel.
3) Clear away area in ground at wireway slot (B) in top of stake (A).
4) Lay 12V cable into wireway slot (B) and screw stem (D) into stake (A).
If assembly does not look straight, adjust by pushing or pulling on stake
only.
5) Screw shade (C) onto stem (D).
6) TURN OFF POWER.
7) Make wire connections using supplied Quic Disc
™ following instructions
below, or using other approved wiring connection method (not supplied.)
8) For CO Finish: Please handle xture with protective gloves as natural oils
from hands can cause an accelerated patina on nish.
Date Issued: 3/9/12IS-15821-US
QUIC DISC™ WIRING INSTRUCTIONS
Turn off power.
The full length of the 18 GA xture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:
• Wiring is to be protected by routing close to the xture or accessory or secured to a building structure such as house or deck.
• 18 GA xture wiring is to be cut off so that it is attached to the connector within 6 inches of the xture or building structure.
• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA xture wire is to be buried.
The Quic Disc™ connector is designed to install one xture and accommodates one 18 GA xture wire and one 10 GA or one 12 GA supply wire.
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
™ or place the 12 gauge supply wire across the area marked 12 GA
on Quic Disc™.
Place the 18 gauge xture wire across the area marked 18 GA on the Quic Disc
™. After the wires are in place, connecta the top of the Quic
Disc™
to the base with supplied screw, making sure that the wires remain at in the bottom portion of the Quic Disc
™, and the screw is tightened
all the way down.
The copper contacts will automatically pierce the wires’ insulation. Excess 18 GA xture wire that sticks out the end of the Quic Disc
™ is to be cut off.
Make no other wiring connections to the 18 GA xture wire.
A
B
D
C
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page
INSTALLATION INSTRUCTIONS
Model 15820 (CP300504, CP300505, CP300506)
Model 15821 (CP300596, CP300597, CP300598)
Produktspezifikationen
| Marke: | Kichler |
| Kategorie: | Lampen |
| Modell: | 15821CBR27 Short Lamp |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kichler 15821CBR27 Short Lamp benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lampen Kichler
Kichler 3694NI Armida Lamp Bedienungsanleitung Kichler 2665PN Hatteras Lamp Bedienungsanleitung Kichler 82366 Merriam Lamp Bedienungsanleitung Kichler 3606AP Olympia Lamp Bedienungsanleitung Kichler 16093CBR VLO Lamp Bedienungsanleitung Kichler 12600WH Horizontal Lamp Bedienungsanleitung Kichler 82353 Soniat Lamp Bedienungsanleitung Kichler 49669WZC Ashland Lamp Bedienungsanleitung
Alle Kichler Lampen Bedienungsanleitungen
Beliebt in Lampen
Kichler 9060BKT Courtyard Lamp Bedienungsanleitung Kichler 15805BKT27R Shallow Lamp Bedienungsanleitung Kichler 9246BA Cylinder Lamp Bedienungsanleitung
Bedienungsanleitung Lampen
Neueste Bedienungsanleitungen für Lampen
Qazqa 91800 Parte Lamp Bedienungsanleitung Trio 508900242 Baroness Lamp Bedienungsanleitung Trio 675610106 Miko Lamp Bedienungsanleitung Qazqa 96518 Cortin Lamp Bedienungsanleitung Westinghouse 6330100 Lamp Bedienungsanleitung Lucide 34409/35/41 Tonio Lamp Bedienungsanleitung Qazqa 98480 Combi Lamp Bedienungsanleitung Lucide 78385/20/11 Kyara Lamp Bedienungsanleitung Verilux VF05 Princeton Lamp Bedienungsanleitung Westinghouse 6222500 Lamp Bedienungsanleitung