Kicker IX500.2 Bedienungsanleitung
Lies die bedienungsanleitung für Kicker IX500.2 (28 Seiten) kostenlos online; sie gehört zur Kategorie Autoradio. Dieses Handbuch wurde von 6 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 3.5 Bewertungen. Hast du eine Frage zu Kicker IX500.2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/28
IX AMPLIFIER
IX500.2
English Version
Versión Español
Amplificador del la Serie IX.2
Deutsche Version
Stereoverstärker der IX.2-Serie
Version Francaise
Amplificateur de série IX.2
LIVIN’ LOUD
2010 IX 500.2 RevF.indd 1
2010 IX 500.2 RevF.indd 1
2010 IX 500.2 RevF.indd 1
2010 IX 500.2 RevF.indd 12010 IX 500.2 RevF.indd 1 11/5/2010 12:31:50 PM
11/5/2010 12:31:50 PM
11/5/2010 12:31:50 PM
11/5/2010 12:31:50 PM11/5/2010 12:31:50 PM
2IX AMPLIFIERS
IX.2-SERIES AMPLIFIERS Owner’s Manual
IX500.2
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er. Use the IXSM or IXSK
mounting kits (sold separately) to stack multiple IX amplifi ers.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: IX500.2
RMS Power
@ 14.4V, 4 stereo, 1% THD+NΩ
@ 14.4V, 2 stereo, 1% THD+NΩ
@ 14.4V, 4 mono, 1% THD+NΩ
125W x 2
250W x 2
500W x 1
Length 9-3/8” (238mm)
Height 2-3/16” (55mm)
Width 7-7/8” (200mm)
Frequency Response ± 1dB 20Hz–20kHz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover Selectable HI/LO/OFF, Variable 50–200Hz, 12dB/octave
Bass Boost Variable 0–18dB @ 40Hz
Maximum Effi ciency (2Ω) >80%
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
IXSK
sold separately
2010 IX 500.2 RevF.indd 2
2010 IX 500.2 RevF.indd 2
2010 IX 500.2 RevF.indd 2
2010 IX 500.2 RevF.indd 22010 IX 500.2 RevF.indd 2 11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM11/5/2010 12:32:10 PM
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
IX500.2 1 x 60 Ampere 4 Gauge PK4, CK4, ZCK4
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The IX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown below (make sure you set
the IX amplifi er’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-
level RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either
input method will provide a low-level output signal at the RCA output, which effectively passes the audio signal
to another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. Install
a second fuse within 18” (45cm) of the amplifi er. If you ever need to remove the amplifi er from the vehicle after it
has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as
when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
12V
18”
(45cm)
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
24”
(60cm)
2010 IX 500.2 RevF.indd 3
2010 IX 500.2 RevF.indd 3
2010 IX 500.2 RevF.indd 3
2010 IX 500.2 RevF.indd 32010 IX 500.2 RevF.indd 3 11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM
11/5/2010 12:32:10 PM11/5/2010 12:32:10 PM
Produktspezifikationen
| Marke: | Kicker |
| Kategorie: | Autoradio |
| Modell: | IX500.2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Kicker IX500.2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autoradio Kicker
29 September 2024
23 September 2024
18 September 2024
16 September 2024
12 September 2024
6 September 2024
31 August 2024
23 August 2024
23 August 2024
22 August 2024
Bedienungsanleitung Autoradio
- SoundMAX
- Majestic
- Tevion
- JVC
- OneConcept
- Sendai
- Spectron
- Orion
- Blaupunkt
- Norauto
- Magnat
- Caliber
- Crunch
- Dension
- Sirius
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
13 Juni 2025
31 Mai 2025
31 Mai 2025
30 Mai 2025
30 Mai 2025
30 Mai 2025