Kicker ZX700.5 Bedienungsanleitung

Kicker Autoradio ZX700.5

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung für Kicker ZX700.5 (28 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
ZX AMPLIFIER
ZX700.5
English Version
Versión Español
Amplificador del la Serie ZX.5
Deutsche Version
StereoverstƤrker der ZX.5-Serie
Version Francaise
Amplificateur de sƩrie ZX.5
LIVIN’ LOUD
2ZX AMPLIFIERS
ZX.5-SERIES AMPLIFIERS Owner’s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
RMS Power:
AMP1 & AMP2 channels driven
@ 14.4V, 4 stereo, 1% THD+NΩ
@ 14.4V, 2 stereo, 1% THD+NΩ
@ 14.4V, 4 mono, 1% THD+NΩ
70W x 4
85W x 4
165W x 2
RMS Power:
SUBWOOFER channel driven
@ 14.4V, 4 mono, 1% THD+NΩ
@ 14.4V, 2 mono, 1% THD+NΩ
210W x 1
420W x 1
Length 20ā€ (507mm)
Specifi cations:
Height 2-1/8ā€ (54mm)
Width 9-5/8ā€ (244mm)
Frequency Response ± 1dB 25Hz–20kHz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Selectable Electronic Crossover Variable HI or OFF (bypass) | 50–200Hz, 12dB/octave
Variable low-pass | 50–200Hz, 24dB/octave (SUB)
Bass Boost Variable 0–18dB @ 40Hz
Subsonic Filter 24dB/octave, fi xed at 25Hz
Pro Tip: To get the best performance from your new KICKER Amplifi er, use genuine KICKER accessories and
wiring.
MODEL: ZX700.5
3
Model External Fuse Power/Ground Wire KICKER Wiring Kit
ZX700.5 1 x 100 Ampere 4 Gauge PK4, CK4, ZCK4
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the ZX
amplifi er’s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to ā€œLOā€. Keep the
audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
GND REM +12V
12V
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£18ā€
(45cm)
ļ‚£24ā€
(60cm)
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
protection LED


Produktspezifikationen

Marke: Kicker
Kategorie: Autoradio
Modell: ZX700.5

Brauchst du Hilfe?

Wenn Sie Hilfe mit Kicker ZX700.5 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Autoradio Kicker

Bedienungsanleitung Autoradio

Neueste Bedienungsanleitung für -Kategorien-