Klipsch Flexus Wall Mount Bedienungsanleitung
Klipsch
Nicht kategorisiert
Flexus Wall Mount
Lies die bedienungsanleitung für Klipsch Flexus Wall Mount (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 3.9 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Klipsch Flexus Wall Mount oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
FLEXUS CORE 200
RIGHT-ANGLE BRACKET
FLEXUS CORE 300
RIGHT-ANGLE BRACKET
MOUNTING TEMPLATE HAS 1.0 INCH (25 MM) SPACING AROUND PERIMETER EXCEPT AS NOTED BELOW
1.0 (FLEXUS CORE 300)
6.5 (FLEXUS CORE 200)
Wood Screw
Anchor Screw
Wood Screw
Anchor
USE PROVIDED T20 DRIVE BIT
#2 PHILLIPS SCREWDRIVER NOT INCLUDED
ANCHOR
(TOGGLE SHOWN IN INSTALL ORIENTATION)
USE PROVIDED FLAT WASHER
WITH BOTH WOOD AND
ANCHOR SCREWS
Screws
FLEXUS CORE 200
Mounting Template
MUST USE ONE OF THESE FIVE SLOT OPENINGS
WHEN MARKING SCREW LOCATIONS ON WALL PER EACH SIDE.
FLEXUS CORE 300
MUST USE ONE OF THESE THREE SLOT OPENINGS
WHEN MARKING SCREW LOCATIONS ON WALL PER EACH SIDE.
Wood Screws
Total Screws
Wall Anchor &
Anchor Screw
Pre Drill
See Note 1
3
0
3 3
2 2
21
2
4 4
2
Note 1
Note 2
Note 3
See Note 2
Centered
Not
Centered
Centered
Not
Centered
16" Stud Wood
Spacing
Keep mounting template against wall. Use a 1/8" (3mm) drill bit and drill through template, drywall, and into stud.
Total pre drill depth 2~2.5 inches.
Mark screw location with sharp object by piercing template. Move folded template below and tape to wall to
help catch drywall debris. Use a #2 Phillips screwdriver, press anchor tip slightly into drywall.Apply pressure,
turn anchor until flush with drywall and arrows on head of anchor point up and down.
24" Stud Wood
Spacing
Concrete, Brick, or Plaster
Use a minimum of 3 fasteners (not included)
NO
NO
1
2
3
Wall mounting template. Don’t discard
during unboxing process.
PREPARE MOUNTING TEMPLATE
ATTACHMENT TO WALL DETAILS
MOUNTING TEMPLATE
Unfold template from its
shipping configuration.
Fold bottom flap and side
flaps along bend lines. Then
tuck triangular flap behind
and insert into vertical slot
opening at each end.
TV
1) ATTACH POWER CORDS AND OTHER
APPLICABLE CABLES TO SOUNDBAR
2) ATTACH SOUNDBAR TO WALL
BRACKET ASSEMBLY AS SHOWN HERE:
FLEXUS 200 SHOWN HERE.
FLEXUS 300 HAS SAME PROCEDURE.
INSTALL AND TIGHTEN APPROPRIATE SCREWS USING PROVIDED FLAT WASHERS.
• THREE WOOD SCREWS ARE SHOWN ABOVE WHICH ARE NOT APPLICABLE TO ALL INSTALLATION SCENARIOS.
• SCREW TYPE AND TOTAL QUANTITY ARE DEPENDENT UPON WOOD STUD SPACING.
• DO NOT OVERTIGHTEN SCREWS.
• A MINIMUM OF THREE SCREWS IS REQUIRED.
FLEXUS CORE 300 RIGHT-ANGLE BRACKET LOCATIONS
5
4
6
FLEXUS CORE 200 RIGHT-ANGLE BRACKET LOCATIONS
V01 - 241002
©2024, Kli ch Group, Inc. Klipsch Group, Inc. is a wholly-owned subsidiary of Voxx International Corporation.ps
Klipsch and Keepers of the Sound are trademarks of Klipsch Group, Inc., registered in the United States and other
countries. The
Bluetooth
®
word mark is a registered trademark owned by Bluetooth SIG, Inc. and any use of such mark by
Klipsch Group, Inc. is under license.
3502 WOODVI RACE, D APO S I SAEW T IN IAN LI , N, U
KLIPSCH.COM
ATTACH WALL BRACKET ASSEMBLY TO WALL
Produktspezifikationen
| Marke: | Klipsch |
| Kategorie: | Nicht kategorisiert |
| Modell: | Flexus Wall Mount |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Klipsch Flexus Wall Mount benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Klipsch
7 Juli 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2024
17 Januar 2024
8 Juli 2023
Bedienungsanleitung Nicht kategorisiert
- Unger
- Taga Harmony
- Trisa
- Ocean Matrix
- Britax
- Caroma
- PAX
- Flycam
- LUCIDA
- MagnaPool
- Trotec
- Vogel's
- Pentair
- Dynavox
- Vax
Neueste Bedienungsanleitung für -Kategorien-
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025