LevelOne IES-0610 Bedienungsanleitung

LevelOne Nicht kategorisiert IES-0610

Lies die bedienungsanleitung für LevelOne IES-0610 (7 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 77 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 39 Bewertungen. Hast du eine Frage zu LevelOne IES-0610 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/7

IES-0610 V2

User Manual

6-Port Gigabit PoE Industrial Switch, 802.3at/af PoE, 4 PoE Outputs, 1 x SFP, 1 x SFP/RJ45 Combo,

-40°C to 75°C, DIN-Rail, 126W

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with th e

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received; including interference that may

cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55032 class for ITE, the essential protection requirement of /24 A

Council Directive 201 3 U on the approximation of the laws of the Member States 4/ 0/E

relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible

that information in this document is not up- -dto ate. Please check with your local

distributors for the latest information. No part of this document can be copied or

reproduced in any form without written consent from the company.

Introduction

This hardened UL60950-1 certified high power POE+ is designed especially for IP

surveillance, traffic monitoring and for a broad range of applications. It accepts 3 power input

sources: PW1, PW2, and Power DIN (via external power adapter) for 48-56VDC power input.

The four PoE+ ports can be used to provide power and data for a variety of PoE devices. It

can be used as a stand-alone device for buses, trucks, and other vehicles for surveillance

purposes. It can also be cascaded/daisy-chained to other devices to cover wider areas via the

uplink ports.

Installation package

This unit can be din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted

brackets are included.

Dip switch function

This unit is equipped with two dip switches,

located on the front panel. Adjusting the dip

switches will change the default function of

this unit. The default manufacturer setting is

SFP for port 5, and 1000M speeds for both

port 5 and port 6 SFP ports. More details are

shown in the chart:

Power connection

This unit provides a 6 pin terminal block. PoE functions can be operated from 48-56VDC

power input. Always make sure your input voltage is within this supported voltage range

for each model.

WARNING – Any exceeded input voltage will not make this unit function and may

damage this unit.

This unit comes with 3 power input sources. P1, P2, and P3.

To connect power: Follow the printed polarity for P1+, P1-, P2+, P2-, and ground. Connect

positive wires to P1+ and/or P2+, connect negative wires to P1- and/or P2-, and connect the

neutral wire to the ground screw as shown.

Power DIN: This unit contains an extra P3 port for power DIN. This power DIN can power

the unit via external power adapter.

Relay: This unit includes an additional 24V@1A relay circuit for special purpose. When 2

powers are connected, the relay is in OPEN mode. If only one of the power sources is

connected, the relay changes to SHORT mode. This relay will only work with P1 and P2. It is

independent from P3.

Power connecting procedure:

STEP 1 – Pull out 6 pin terminal block

STEP 2 – Connect wire to P1+, P1-, P2+, P2-, and the neutral wire to the ground screw.

STEP 3 – Plug connected 6 pin terminal block back into place. Or, Connect the P3 power DIN

from external power adapter.

WARNING – Always SHUT OFF power source to connect power wire.

WARNING – Always ground the power source to maintain a clean power input. Cheaply

made power supplies create too much noise and will cause the power input to fluctuate

when connected to this unit. To avoid this, always ground the power source to maintain a

clean power input.

Produktspezifikationen

Marke:	LevelOne
Kategorie:	Nicht kategorisiert
Modell:	IES-0610
Breite:	40 mm
Tiefe:	105 mm
Gewicht:	720 g
Produktfarbe:	Schwarz
Höhe:	38 mm
Energieschutzeigenschaften:	Overload, Reverse polarity
Betriebstemperatur:	-40 - 75 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Verpackungsbreite:	215 mm
Verpackungstiefe:	165 mm
Verpackungshöhe:	65 mm
Paketgewicht:	120 g
Netzstandard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Schnellstartübersicht:	Ja
Vollduplex:	Ja
Stromverbrauch (Standardbetrieb):	6 W
Power over Ethernet (PoE):	Ja
Warentarifnummer (HS):	85176990
Ursprungsland:	Taiwan
Verpackungsart:	Box
LED-Anzeigen:	Activity, Link, Power
Temperaturbereich bei Lagerung:	-40 - 85 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Anzahl der basisschaltenden RJ-45 Ethernet Ports:	4
Basic Switching RJ-45 Ethernet Ports-Typ:	Gigabit Ethernet (10/100/1000)
Auto MDI/MDI-X:	Ja
10G-Unterstützung:	Nein
MAC-Adressentabelle:	1024 Eintragungen
Routing-/Switching-Kapazität:	12 Gbit/s
Anzahl Combo-SPF-Anschlüsse:	1
Eingangsspannung:	48 - 55 V
Wandmontage:	Ja
Store-and-Forward:	Ja
Auto-Negotiation-Funktion:	Ja
Unterstützung Datenflusssteuerung:	Ja
Jumbo-Frames:	10000
Datenpaket-Pufferspeicher:	1 MB
Menge SFP-Modul-Steckplätze:	1
Anzahl Power over Ethernet plus (PoE+) Anschlüsse:	4
Gesamtleistung Power over Ethernet (PoE):	126 W
Power over Ethernet (PoE) Leistung pro Anschluss:	30 W
Terminalblock-Anschluss:	Ja
DIN-Schienen-Montage:	Ja
Paketweiterleitungsrate (1 Gbit/s):	148800 pps
Paketweiterleitungsrate (100 Mbit/s):	148000 pps
Paketweiterleitungsrate (10 Mbit/s):	14880 pps