Leviton SGVSM-W Bedienungsanleitung
Lies die bedienungsanleitung für Leviton SGVSM-W (2 Seiten) kostenlos online; sie gehört zur Kategorie Regler. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu Leviton SGVSM-W oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Strauss™ Volume Control
200 Watts (100 RMS)
Cat. No. SGVSM
DI-000-SGVSM-00A
INSTALLATION
WARNING: TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND
REGULATIONS.
WARNING: MAXIMUM AMPLIFIER POWER IS 100 WATTS PER CHANNEL. HIGHER AMPLIFIER POWER MAY
CAUSE DAMAGE.
Before starting connections, please note that the left and right attenuator circuits are completely isolated from each other
to prevent instability when used with certain types of amplifiers which have floating grounds. If the amplifier to be used
has common grounds between channels, a 3 wire system can be used between the amplifier and control, but it will be
necessary to connect a jumper between the control ground returns (L- & R-).
If one ground is open, there will be no output on the ungrounded channel at any attenuator setting.
The connectors on the attenuator are the screw-to-tighten type. Connect wires per WIRING DIAGRAM as follows:
1. Select location for mounting control.
NOTE: Due to the depth of volume control, a low-voltage ring or deep electrical box is recommended.
2. Make connections by stripping wire insulation back about 1/4” (.63 cm). Twist any loose strands tightly.
NOTE: It is recommended that at least 16 AWG speaker wire be used for runs up to 30’ (9.1 m). For runs longer than
30’ (9.1 m), use 14-18 AWG wire.
3. Insert the wires from the amplifier into the “TO AMP” openings of the connector, Positive-to-Positive and Negative-to-
Negative, then tighten screws. Check for stray wire strands that might cause a short circuit. Make sure the metal part of
the screw connector engages the bare wire, NOT the insulation!
4. Similarly, connect speaker wires to the “TO SPEAKER” openings and tighten screws.
IMPEDANCE NOTE: There are two impedance settings. 2x is used for up to four rooms connected to a single 8 ohm
rated amplifier output and 6x which is used for 5 to six rooms.
5. ensuring that terminal connector is at top. Install control in its operating location,
NOTE: Leave control 3 or 4 positions above minimum volume before starting the system for the first time to avoid
damaging the speakers, while still being loud enough to observe operation.
INSTALLATION MANUAL
DI-000-SGVSM-00A
SPECIFICATIONS
Attenuator Type: Ceramic Resistive Network
Switch: 12 position slider, make-before-break contacts, low torque specifications for smooth feel
Connector: Screw-tight type, removable connector block
Amplifier Power Rating: 200 Watts (100 RMS)
Impedance Matching: 2 x 8 Ohms
(provided by jumpers) 6 x 47 Ohms
Frequency Response: 20-20kHz +/- 1db, 4-16 Ohm load
Attenuation: 36db
Produktspezifikationen
| Marke: | Leviton |
| Kategorie: | Regler |
| Modell: | SGVSM-W |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Leviton SGVSM-W benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Regler Leviton
21 August 2024
19 August 2024
Bedienungsanleitung Regler
- Denon
- Morningstar
- Nedis
- Saramonic
- Heritage Audio
- SPL
- Re.corder
- Hunter
- Sony
- Gefen
- Huawei
- Music Hall
- AirTurn
- Polsen
- Zoom
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
5 Oktober 2024
4 Oktober 2024
3 Oktober 2024
1 Oktober 2024
Hori Force Feedback Truck Control System Bedienungsanleitung
1 Oktober 2024
30 September 2024
27 September 2024