Liberty Pumps LE51M Bedienungsanleitung
Liberty Pumps
Pumpe
LE51M
Lies die bedienungsanleitung für Liberty Pumps LE51M (28 Seiten) kostenlos online; sie gehört zur Kategorie Pumpe. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 3.5 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Liberty Pumps LE51M oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/28
7000 Apple Tree Avenue
Bergen, NY 14416
Phone: (800) 543-2550
Fax: (585) 494-1839
www.libertypumps.com
IMPORTANT:
Prior to installation, record Model, Serial Number, and
Code Number from pump nameplate for future reference.
MODEL ______________________
SERIAL ______________________
CODE ______________________
INSTALLATION
DATE ______________________
©Copyright 2015 Liberty Pumps Inc. All rights reserved
Contents
1.) General Information
2.) The Basin
3.) Installation
4.) Electrical Service and Operation
5.) Maintenance and Troubleshooting
6.) Warranty
Installation Manual 7034000L
LE and LEH Series Sewage Pumps
Models
LE40-Series 4/10 HP
LE50-Series 1/2 HP
LE70-Series 3/4 HP
LE100-Series 1 HP
LEH100-Series 1 HP
LEH150-Series 1.5 HP
LEH200-Series 2 HP
*Do not throw away or lose this manual.
©Copyright 2015 Liberty Pumps Inc. All rights reserved 2
Before Installation, read the following instructions carefully. Each Liberty pump is individually factory tested to assure
proper performance. By closely following these instructions, potential operating problems should be eliminated, providing
years of trouble-free service.
Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments.
The electrical connections and wiring for a pump installation should only be made by qualified personnel.
This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric
shock, be certain that it is connected only to a properly grounded, grounding-type receptacle.
Always wear rubber boots when water is on the floor and you must unplug the pump.
DO NOT bypass grounding wires or remove ground prong from attachment plugs.
DO NOT use an extension cord.
This pump requires a separate, properly fused and grounded branch circuit. Make sure the power source is properly
sized for the voltage and amperage requirements of the pump, as noted on the nameplate.
The electrical outlet shall be within the length limitations of the pump power cord, and at least 4 feet above floor level
to minimize possible hazards from flood conditions.
The installation must be in accordance with the National Electric Code, Uniform Plumbing Code, International
Plumbing Code, as well as all applicable local codes and ordinances.
Sump and sewage pumps often handle materials which could cause illness or disease. Wear adequate protective
clothing when working on a used pump or piping.
Never enter a pump basin after it has been used. Sewage and effluent can emit several gases which are poisonous.
Keep clear of suction and discharge openings. To prevent injury, never insert fingers into pump while it is plugged in.
DO NOT use this product for flammable or corrosive liquid.
DO NOT use this product in applications where human contact with the pumped fluid is common (such as swimming
pools, fountains, etc.)
NEVER dispose of materials such as paint thinner or other chemicals down drains, as they can chemically attack and
damage pump components, potentially causing product malfunction or failure.
DO NOT use pumps in water over 140F (60C).
DO NOT use pumps in mud, sand, cement, oil or chemicals.
DO NOT modify the pump in any way.
DO NOT lift or carry pump by power cord.
DO NOT remove any tags from pump or cords.
If pump is installed during construction before power is available, it must be protected from the environment to prevent
water from entering through the cord plug end, etc.
Disconnect old pump from power source before handling.
Separate the discharge pipe at either the check valve or at the union. If neither a check valve nor a union is part of the
existing discharge pipe, cut the pipe with a hacksaw and remove the pump (A union or check valve will need to be
installed at this cut).
1. General Information
Produktspezifikationen
| Marke: | Liberty Pumps |
| Kategorie: | Pumpe |
| Modell: | LE51M |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Liberty Pumps LE51M benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Pumpe Liberty Pumps
19 Juli 2025
19 Juli 2025
19 Juli 2025
19 Juli 2025
Bedienungsanleitung Pumpe
- Pontec
- Metabo
- Quigg
- AstralPool
- Elpumps
- BBB
- Enermax
- Little Giant
- Neptun
- Draper
- Germania
- Makita
- Tacklife
- Fuxtec
- Ambiano
Neueste Bedienungsanleitung für -Kategorien-
19 Juli 2025
19 Juli 2025
19 Juli 2025
18 Juli 2025
18 Juli 2025
18 Juli 2025
18 Juli 2025
18 Juli 2025
18 Juli 2025
17 Juli 2025