LiftMaster 880LMW Bedienungsanleitung

Lies die bedienungsanleitung für LiftMaster 880LMW (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 21 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 11 Bewertungen. Hast du eine Frage zu LiftMaster 880LMW oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

1

Smart Control Panel®

Safety Reversing Sensors

SMART CONTROL PANEL®

Model 880LMW

To prevent possible SERIOUS INJURY or DEATH from

electrocution:

• Be sure power is NOT connected BEFORE installing door

control.

• Connect ONLY to 12 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing

garage door:

• Install door control within sight of garage door, out of reach

of children at a minimum height of 5 feet (1.5 m), and away

from ALL moving parts of door.

• NEVER permit children to operate or play with door control

push buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed.

NEVER permit anyone to cross path of closing garage door.

FEATURE OVERVIEW

The features are adjustable and may be turned off or on as desired. Refer to the Feature Settings section.

A

A

SCREEN

The screen will display the time and temperature until the menu

button is pressed, and then it will display the menu options. If

there is a problem with the garage door opener the screen will

display the Diagnostic Code.

LIGHT BUTTON

Press the LIGHT button to turn the garage door opener lights on or

off. When the lights are turned on they will stay on until the LIGHT

button is pressed again, or until the garage door opener is

activated. Once the garage door opener is activated the lights will

turn off after the specified period of time (the factory setting is

4-1/2 minutes). The LIGHT button will not control the lights when

the door is in motion. The duration of the light timing can be

adjusted by accessing the menu using the navigation buttons.

MOTION SENSOR

The motion sensor will automatically turn on the garage door

opener lights when motion is detected. The lights will come on for

the set period of time, then shut off. The factory setting is on and

set at 4-1/2 minutes.

LOCK

The LOCK feature is designed to prevent activation of the garage

door opener from remote controls while still allowing activation

from the door control and keyless entry. This feature is useful for

added peace of mind when the home is empty (i.e. vacation).

TIMER-TO-CLOSE (TTC)

DO NOT enable TTC if operating a one-piece door. TTC is to be

used ONLY with sectional doors. Factory default is set to off. TTC

can be set to automatically close your garage door from the fully

open position after a specified period of time (1, 5, 10 minute

intervals or a custom setting up to 99 minutes). The garage door

opener will beep and the lights will flash before closing the door.

The screen on the door control can display the status of the TTC.

TTC WILL NOT work if the garage door opener is operating by

battery power or if the safety reversing sensors are misaligned.

This feature is NOT intended to be the primary method of closing

the door. A keyless entry should be installed in the event of an

accidental lock out when using this feature.

MAINTENANCE ALERT SYSTEM (MAS)

This feature assists the homeowner in ensuring the garage door

opener system stays in good working condition. A maintenance

alert message will display on the screen indicating the garage door

opener may be in need of maintenance.

The MAS feature MUST be activated at time of installation. The

factory setting is off.

WARNING: This product can expose you to chemicals including

lead, which are known to the State of California to cause cancer or

birth defects or other reproductive harm. For more information go

to www.P65Warnings.ca.gov.

Produktspezifikationen