Lightware WP-HDMI-TPS-RX97-EU Bedienungsanleitung

Lightware AV extender WP-HDMI-TPS-RX97-EU

Lies die bedienungsanleitung für Lightware WP-HDMI-TPS-RX97-EU (2 Seiten) kostenlos online; sie gehört zur Kategorie AV extender. Dieses Handbuch wurde von 26 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 13.5 Bewertungen. Hast du eine Frage zu Lightware WP-HDMI-TPS-RX97-EU oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/2

Quick Start Guide

WP-HDMI-TPS-RX97-EU, -EUROMOD, -UK, -US

FP-HDMI-TPS-RX97-GB3, -LEGRAND - CRFB

Further Information

The product brief and further information of this appliance is available at www.lightware.com.

See the Downloads section on the on the dedicated product page.

[email protected]

+36 1 255 3800

[email protected]

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: v1.1

19200107

Important Safety Instructions

Please read the supplied safety instruction document before using the product and keep it

available for future reference.

Introduction

WP/FP-HDMI-TPS-RX97 series twisted pair HDBaseT

extenders provide

extension of uncompressed 4K/UHD video with embedded audio (up to eight

channel PCM or HBR audio) for long distances over a single CATx cable.

The thoroughly redesigned form factor of the wall and oor panels allows for easier

connecting and removing cables in narrow spaces (behind TV sets, under oor panel lids)

and reduces cable bending and breaking. The built-in cable tie-down points further ensure

stable connection and reduce cable stress.

Box Contents

Receiver unit Safety and Warranty info,

Quick Start Guide

Phoenix combicon

3-pole connector

Status LEDs The LEDs give feedback about the state of the unit and the

video signals. See Status LEDs for the details.

IR input/output 2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the

detector, IR OUT for the emitter).

RS-232 connector 3-pole Phoenix connector for RS-232 serial port. Firmware

upgrade can also be performed over this interface.

Ethernet Locking RJ45 connector for Ethernet communication.

HDMI output HDMI output for DVI or HDMI signal. Connect an HDMI

cable between the receiver and the display device.

TPS input port Locking RJ45 connector for HDBaseT

signal transmission.

Connect a twisted pair cable between the transmitter and the

receiver.

Tie-down point The built-in tie-down points are designed to clamp the

HDMI and the CATx cable and ensure stable connection.

Please see the enlarged picture below.

Front and Rear View (WP-HDMI-TPS-RX97-US)

Connecting Steps Status LEDs

SIGNAL

 OFF: no video signal transmission is present.

 ON: video signal transmission is present.

LINK

 OFF: TPS connection failed between the devices.

 BLINKING: TPS connection is detected and Low

Power Partial Functionality (LPPF) link mode is

active.

 ON: TPS connection is detected and HDBaseT

(HDBT) or Long reach (LR) link mode is active.

LIVE

 OFF: no power supply or out of order.

 BLINKING: device is powered and ready to use.

Bottom View (WP-HDMI-TPS-RX97-US)

RS-232 Switch Modes



Please note that the 48V power adaptor is an optional accessory which can be purchased

separately.

RS-232 switch Normal: serial data is passed through the device.

Prog: RS-232 pass-through function is disabled, the device

is ready for the rmware upgrade (see RS-232 switch

modes section for details).

TPS mode switch LR: Longreach TPS mode; lower resolution (max 1080p),

longer distances.

Auto: TPS mode is determined automatically.

DC Input Connect the output to the 3-pole Phoenix connector on the

bottom of the wall plate.

CATx

DVI

Connect the TPS output port of the receiver to the TPS+PoE port of the

TPS-PI-1P1 by a CATx cable.

Connect the receiver (or the Matrix input board) to the power injector by a

CATx cable via the TPS port.

HDMI

Connect the sink (e.g. Projector) to the HDMI output port by HDMI cable.

RS-232

Optionally for RS-232 extension: connect a controller/controlled device

(e.g. Projector) to the RS-232 port.

Optionally for Infrared extension:

 Connect the IR emitter to the IR OUT port of the receiver, and/or

 Connect the IR detector to the IR IN port of the receiver.

LAN

Optionally connect the receiver to a LAN.

Power

Powering on the devices is recommended to do as the nal step during

the installation. Please check the Power Supply Options section for the

details.



WP-HDMI-TPS-RX97 series have the same connectors but the dimensions are different.

The product is compatible with any HDBaseT

third party devices.

HDBaseT

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Power Supply Options

TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -

and can receive power over the TPS line.

The extender can be powered by any of the following ways:

1. Local adaptor 2. Remote power injector 3. Matrix board



TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power

the WP-HDMI-TPS-TX/97 series and vica versa. WP-UMX-TPS-TX97 series contains PoE-

compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can be

remote powered only by each other.



Warranty void if damage occurs due to the usage of a different power source.

Typical Application

HDMI

Compatible

Transmitter or

Input Board

WP-HDMI-TPS-RX97

Power adaptor

IR detector

Ethernet

Projector

Power

LAN

RS-232

WP-HDMI-TPS-RX97-US

HDMI OUTEthernet

TPS-PI-1P1

Power injector

CATx

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

23 11 5

switch

Programming

TPS port

RS-232

normal

prog

48V DC

Power

adaptor

TPS-PI-1P1

CATx

(TPS)

Power

send

48V DC

Power

adaptor

MX-TPS2-IB-P

DC IN

8 CH TPS INPUT BOARD WITH POE

48V 5A

- +

Ethernet

TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4

8CH INPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO

MX-HDMI-3D-IB-A

IN 1

IN 2

IN 3

IN 4

MX-TPS2-OB-S

48V 5A

DC IN

8 CH TPS OUTPUT BOARD WITH DIGITAL AUDIO

12V power on TPS connector. Only use with compatible devices!

TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4

8CH OUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO

MX-HDMI-3D-OB-A

OUT 1

OUT 2

OUT 3

CATx

(TPS)

External

power supply

Power send

ypical: 0.5A

Max: 1.25A

- +

Max:2.5A

mm2 :NIP

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDMI-TPS-RX97-US

HDMI OUTEthernet

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDMI-TPS-RX97-US

HDMI OUT

Ethernet

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDMI-TPS-RX97-US

HDMI OUTEthernet

Compatible Devices

TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90

series.

IR cable

Serial

cable

IR emitter

HDMI

Blu-Ray or DVD Player

LAN

Ethernet switch

HD Projector

Touch panel

Sn:

Made in EU, Hungary

RoHS

Ethernet 10/100

Bidirectional IR

Bidirectional RS-232

TTPPSS LLoonngg DDiissttaannccee TTrraannssmmiitttteerr

HDMI, 3D, 4K supported

For best performance use AWG23 CAT6 or CAT7 SFTP cable

PIN: 2mm

12V 1A DC

--T

Device can be remote powered over TPS link with PoE

(IEEE 802.3af)

TPS OUT

PoE

( )

TPS-PI-1P1

LAN

HDMI-

TPS-TX97

48V DC

Power

adaptor

LAN

IR detector

HDMI

IR cable

Serial cable

ETHE RNET

Laptop

WP-HDMI-TPS-RX97-US

ypical: 0.5A

Max: 1.25A

- +

Max:2.5A

mm2 :NIP

IR OUT

IR IN

LINK

TX RX

LIVE

SIGNAL

WP-HDMI-TPS-RX97-US

HDMI OUTEthernet

CATx

TPS connection

CATx up to 170m

Power

send

WP-HDMI-TPS-RX97-US

HDMI OUTEthernet

Wiring Guide for RS-232 Data Transmission

WP/FP-HDMI-TPS-RX97 series are built with 3-pole Phoenix connector. See the below

examples of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data

Terminal Equipment) type device:

Lightware device and a DCE

D-SUB 9 - Phoenix

Lightware device and a DTE

D-SUB 9 - Phoenix

TX RX

2: TX data transmit

3: RX data receive

5: Ground

TX RX

2: TX data receive

3: RX data transmit

5: Ground

For more information about the cable wiring see the user’s manual of the device or

Cable Wiring Guide on our website www.lightware.com/support/guides-and-white-papers.

LINKLIVE

SIGNAL

LINKLIVE

SIGNAL

LINKLIVE

SIGNAL

Safety and

Warranty

Info

Quick

Start

Guide

IR IN

SIGNAL

HDMI OUT

Produktspezifikationen

Marke:	Lightware
Kategorie:	AV extender
Modell:	WP-HDMI-TPS-RX97-EU
WLAN:	Nein
Bluetooth:	Nein
Breite:	100.4 mm
Tiefe:	100.4 mm
Gewicht:	330 g
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabelgebunden
Höhe:	26 mm
Material:	Metall
Gleichstrom-Anschluss (DC):	Ja
Zertifizierung:	CE
Stromverbrauch (Standardbetrieb):	5.3 W
Power over Ethernet (PoE):	Ja
Typ:	AV-Receiver
LED-Anzeigen:	Ja
HDCP:	Ja
Unterstützte Grafik-Auflösungen:	1920 x 1080 (HD 1080)
3D:	Ja
Maximale Auflösung:	4096 x 2048 Pixel
HDMI-Version:	1.4a
Eingangsstrom:	2.5 A
Wandmontage:	Ja
Anzahl der HDMI-Ausgänge:	1
Arbeitsspannung:	12 V
Anzahl serielle Anschlüsse:	1
unterstütze Kabeltypen:	Cat5, Cat6, Cat7
Bandbreite:	3.4 Gbit/s
Fernbedienung (IR) output:	1
Fernbedienung (IR) input:	1
Consumer Electronics Control (CEC) Unterstützung:	Ja
HDCP-Durchschleifung:	Ja
Stromverbrauch (Empfänger) (max.):	6.1 W
IR-Durchgang (Pass Through):	Ja
RS-232-Durchschleifung:	Ja
Ethernet/LAN:	Ja
EDID-Speicher (TX):	Ja
EDID-Emulation (TX):	Ja
Keine Videokompression:	Ja