Lightware WP-UMX-TPS-TX120-US Bedienungsanleitung

Lies die bedienungsanleitung für Lightware WP-UMX-TPS-TX120-US (2 Seiten) kostenlos online; sie gehört zur Kategorie AV extender. Dieses Handbuch wurde von 29 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 15 Bewertungen. Hast du eine Frage zu Lightware WP-UMX-TPS-TX120-US oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Quick Start Guide

WP-UMX-TPS-TX-120-US Black, White

WP-UMX-TPS-TX130-US Black, White

FP-UMX-TPS-TX130-MKM

Further Information

The document is valid with the following rmware version: 1.3.0

The User’s manual of this appliance is available on www.lightware.com.

See the Downloads section on the dedicated product page.

Contact Us

[email protected]

+36 1 255 3800

[email protected]

+36 1 255 3810

Lightware Visual Engineering LLC.

Peterdy 15, Budapest H-1071, Hungary

Doc. ver.: 2.3

19200113

Optional Accessories

The following accessories can be purchased separately:

Compatible Devices

The transmitters are compatible with all Lightware TPS receivers, matrix boards and third-party

devices based on HDBase-T

TM

technology.

Important Safety Instructions

Please read the supplied safety instruction document before using the product and keep it

available for future reference.

Introduction

Lightware’s WP/FP-UMX-TPS extenders transmit universal video at a resolution up to

4K, audio and control up to 170 m distance over a single CATx cable. The products have

HDBaseT

TM

integration with additional Lightware developments. This transmitter was designed

for digital and analog video and audio signals e.g. DVI, VGA, HDMI1.4 and DP 1.1 with analog

stereo audio from local inputs or embedded 7.1 HBR audio and to handle HDCP encryption.

Box Contents

Power Supply Options

The transmitter can be powered by any of the following ways:

1. Local adaptor 2. Remote power injector 3. Matrix board

Transmitter unit

Mounting screws (4 pcs.

6-32 x 1”, oval head)

1

Phoenix Combicon

3-pole connector

Safety and Warranty Info,

Quick Start Guide

1

Status LEDsThe LEDs give feedback about the state of the unit, the

video and audio signals. See the attached list for details.

2

Show p1-me ButtonSpecial functions are available with this button (e.g. enable

DHCP (dynamic IP) or restore factory default settings).

3

Reset ButtonThe same as disconnecting the device from the power

source and reconnecting it again.

4

IR DetectorIR Detector can sense IR light which can be forwarded to

the receiver side or use for controlling functions.

5

HDMI InputInput for a digital video source. Applied cable shall not be

more, than 30 m (at 1080p) and 15 m (at 4K).

6

DisplayPort InputInput for digital video source (only on TX130 models). Applied

cable shall not be more, than 30 m (at 2.7 Gbps data speed).

7

Audio Input3.5 mm Jack connector for unbalanced analog audio signal.

8

VGA InputInput for an analog video source. Using a VGA cable where

all the pins are wired (DDC channel) is highly recommended.

9

EthernetLocking RJ45 connector for Ethernet communication.

q

Video SelectManual switching between the video inputs.

w

Audio SelectManual switching between the audio inputs.

1

TPS Output PortLocking RJ45 connector for CATx cables to a TPS receiver

unit. Remote powering also happens through this connector.

2

RS-232 Port3-pole Phoenix connector for RS-232 serial port.

3

DC Input48V DC input connector for local powering.

Front View

Rear View

The product is compatible with any HDBaseT

TM

third party devices.

HDBaseT

TM

and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Connecting Steps

Front View Legend



Warranty void if damage occurs due to the usage of a different power source.



Please note that the 48V power adaptor is an optional accessory which can be purchased

separately.



TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power

the WP-UMX-TPS-TX100 series and vica versa. WP-UMX-TPS-TX100 series contains PoE-

compatible remote power function, RX95 and TX95 extenders can be remote powered only

by each other.

Front Panel LEDs

Video sources

OFF: video source is not selected.

BLINKING: video source is selected but not active.

ON: video source is selected and active.

Audio sources

OFF: audio source is not selected.

BLINKING: audio source is selected but not active.

ON (with short pause): audio source is selected and the

port is active but not embedded to the output video stream.

ON: audio source is selected, the port is active and the audio is embedded in the video.



When Autoselect is enabled and video signal is not present at all, video LEDs blink.

Autoselect LED

OFF: autoselect is disabled.

BLINKING: autoselect is enabled; searching for signal

(video LEDs also blink).

ON: autoselect is enabled; active video signal is found.



A port is active if there is a valid signal on it.

TPS LINK

OFF: no TPS link between transmitter and receiver.

BLINKING (slow): low power mode is active.

BLINKING (fast): Ethernet fallback mode is active.

ON: TPS link is established, HDBaseT or Long Reach mode is active.

CATx

Connect the transmitter and a compatible receiver or the matrix input board by

a CATx cable via the TPS connectors.

HDMI

DP

VGA

Connect the transmitter and the sources using the inputs and VGA / DVI-I /

HDMI / DisplayPort cables.

Audio

Optionally connect an asymmetric audio device with unbalanced audio signal

(e.g. a VGA laptop) to the 2.5" TRS (jack) audio input port.

LAN

Optionally connect the transmitter to a LAN network in order to control the

device.

RS-232

Optionally connect a controller/controlled device (e.g. relay box) to the serial port.

Power

See the Power Supply Options section.

Mounting screws (4 pcs.

3.9x 22mm, PZ at-head)

2

1

For white models in

WP-UMX-TPS-100 series.

2

For black models in

WP-UMX-TPS-100 series.

Switch/outlet box

(B225R) for mounting

48V DC power adaptor with

interchangeable plugs

Safety and

Warranty

Info

Quick

Start

Guide

For more information about the cable wiring see the user’s manual of the device or the Cable

Wiring Guide on our website www.lightware.com/support/guides-and-white-papers.

Wiring Guide for RS-232 Data Transmission

The transmitters are built with 3-pole Phoenix connector. See the below examples of

connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data Terminal

Equipment) type device:

q

9

8

5

4

w

3

1

76

2

3

2

1

Lightware device and a DCE

D-SUB 9 – Phoenix

Lightware device and a DTE

D-SUB 9 – Phoenix

TX RX

1

6

9

5

2: TX data transmit

3: RX data receive

5: Ground

TX RX

1

6

9

5

2: TX data receive

3: RX data transmit

5: Ground

VIDEO

Autoselect

HDMI

DP

VGA

AUDIO

T

P

S

L

I

N

K

HDMI

DP

AUDIO

VIDEO

Autoselect

HDMI

DP

VGA

AUDIO

T

P

S

L

I

N

K

HDMI

DP

AUDIO

VIDEO

Autoselect

HDMI

DP

VGA

AUDIO

T

P

S

L

I

N

K

HDMI

DP

AUDIO

VIDEO

Autoselect

HDMI

DP

VGA

AUDIO

TPS LINK

HDMI

DP

AUDIO

VGA laptop

HDMI laptop

Power

EthernetPower adaptor

WP-UMX-TPS-TX100

series transmitter

MacBook

HDMIVGADPAudio

Relay box

LAN

RS-232

CATx

Compatible

receiver or

input board

WWPP--UUMMXX--TTPPSS--TTXX113300--UUSS

VIDEO

Autoselect

HDMI

INPUT STATUS

SHOW

ME

DP

VGA

AUDIO

TPS LINK

HDMI

DP

AUDIO

AUDIO

SELECT

IR

VIDEO

SELECT

RESET

Ethernet

AUDIO IN

HDMI IN

VGA IN

DP IN

48V DC

Power

adaptor

WP-UMX-TPS-TX130-US

VIDEO

SELECT

ETHERNET

INPUT STATUS

VIDEO AUDIO

O

RESET

IR

VGA

DP

HDMI

Autoselect

AUDIO

SELECT

SHOW

ME

2 DP IN

3

AUDIO

DP

HDMI

TPS Link

TPS-PI-1P1

48 DC IN

Typical: 0.7A

Max: 1.5A

- +

Max:2.5A

PIN: 2mm

CATx

(TPS)

Power

send

48V DC

Power

adaptor

WP-UMX-TPS-TX130-US

VIDEO

SELECT

ETHERNET

INPUT STATUS

VIDEO AUDIO

O

RESET

IR

VGA

DP

HDMI

Autoselect

AUDIO

SELECT

SHOW

ME

2 DP IN

3

AUDIO

DP

HDMI

TPS Link

MX-TPS2-IB-P

DC IN

8 CH TPS INPUT BOARD WITH POE

48V 5A

- +

Ethernet

TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4

8CH INPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO

MX-HDMI-3D-IB-A

IN 1

IN 2

IN 3

IN 4

MX-TPS2-OB-S

48V 5A

DC IN

8 CH TPS OUTPUT BOARD WITH DIGITAL AUDIO

12V power on TPS connector. Only use with compatibledevices!

12V power on TPS connector. Only use with compatibledevices!

TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4

8CH OUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO

MX-HDMI-3D-OB-A

OUT 1

OUT 2

OUT 3

CATx

(TPS)

External

power supply

Power send

WP-UMX-TPS-TX130-US

VIDEO

SELECT

ETHERNET

INPUT STATUS

VIDEO AUDIO

O

RESET

IR

VGA

DP

HDMI

Autoselect

AUDIO

SELECT

SHOW

ME

2 DP IN

3

AUDIO

DP

HDMI

TPS Link

Produktspezifikationen