Manhattan 180535 Bedienungsanleitung
Manhattan
Nicht kategorisiert
180535
Lies die bedienungsanleitung für Manhattan 180535 (16 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 8 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 4.5 Bewertungen. Hast du eine Frage zu Manhattan 180535 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/16
For additional benefits
10-Port AC
Charging Cabinet
Instructions
Model 180535
or visit: register.manhattanproducts.com/r/180535
Scan to
register your
product warranty
For specifications, please visit manhattanproducts.com register.. Register your product at
manhattanproducts.com/r/180535 or scan the QR code on the cover.
Setup
1 Unlock unit door and open it.
2 To fit larger devices, remove bay divider(s).
• Unscrew bar and set it aside.
• To remove divider, pull up on the clip to release it from the bar it’s attached to.
• When enough dividers are removed, replace numbered bar and screws.
3 Connect devices to power outlets with appropriate cables. Secure cables with wire clips on dividers.
• Remove screws that hold the power box in place; slide the power box out.
• Connect power cables to power outlets, feeding cables through holes on power panel.
• Push the power box back in and replace the screws that hold it in place.
• Load devices in bays.
• Connect cables to devices.
Charging
4 Connect unit power cable to power outlet. Unit automatically begins to charge devices.
Installation Options
The following sections offer optional steps to complete installation.
To Reverse the Door — NOTE: Make sure all power is cut off from unit!
1 Unscrew grounding cable from door and cabinet. Remove door from cabinet by pulling L-shaped pins.2
1
3
2
Instructions
English
3 Flip door and guide pins into holes on other side of
cabinet frame. Release pins and ensure door is
secure.
4 Reattach grounding cable to door and cabinet.
Mounting to the Wall
1 At desired location on wall, use the spacing
shown in the graphic below to mark four level
drill positions for the cabinet holes.
Concrete wall: use a 15/64” (6 mm) bit to drill
holes 2.4 in. (60 mm) deep at marks.
Wood-stud walls: use a 15/64” (6 mm) bit to
make pilot holes 2.4 in. (60 mm) deep at marks.
2 Install included screws into holes so they
protrude 0.4 in. (10 mm) from the wall.
3 Position cabinet holes over wall screws and
hang cabinet on them. Installation is complete.
Stacking the Units — NOTE: Make sure all power is cut off from unit!
Stacking material not included; refer to website.
1 Unscrew the screws on the power box.
2 Slide the power box out.
3 Align the stacking holes on the top and bottom of
the cabinets.
4 Tighten screws (not included) into both cabinets
from the ceiling of the bottom cabinet.
5 Reinstall the power box with its screws.
16in. (406.4 mm)
16.57in. (420.86mm)
2 in.
(50mm)
NOTE: a 13 mm
(0.51 in.) gap exists.
3
Instructions
English
Produktspezifikationen
| Marke: | Manhattan |
| Kategorie: | Nicht kategorisiert |
| Modell: | 180535 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Manhattan 180535 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Manhattan
15 Juni 2025
6 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
4 September 2024
3 September 2024
3 September 2024
3 September 2024
Bedienungsanleitung Nicht kategorisiert
- Alga
- Strex
- Sparco
- Nxg
- Thorens
- DIEZEL
- Kenmore
- Patton
- Muse
- Winston
- RF Elements
- Fisher-Price
- Natec
- JBC
- GPX
Neueste Bedienungsanleitung für -Kategorien-
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025