Maverick MTX-244 Bedienungsanleitung

Maverick ferngesteuertes Spielzeug MTX-244

Lies die bedienungsanleitung für Maverick MTX-244 (12 Seiten) kostenlos online; sie gehört zur Kategorie ferngesteuertes Spielzeug. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 2 Bewertungen. Hast du eine Frage zu Maverick MTX-244 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/12

INSTRUCTIONS

Throttle Trigger

1. Power LED

2. Steering Reverse Switch

3. Throttle Reverse Switch

4. Throttle End Point Dial (low/high points)

5. Bind Button

6. Throttle Trim

7. Steering Trim

8. Steering Dual Rate (D/R) Switch

9. Steering Control

10. Throttle Trigger

11. Power Switch

• Pull the trigger to go forwards and

speed up

• Push the trigger forward to brake

• Push again for reverse

Turn the steering wheel to the left

or right to make the vehicle turn left

or right

The Steering (ST) and Throttle (TH)

reverse switches are set to “NOR”

(Normal) as standard. To switch

the direction of travel of either the

steering or throttle move the switch

to the “REV” (Reverse) position.

The dual rate settings adjust the

maximum degree of movement from

the servo.

Move the D/R lever down to increase

or up to decrease the maximum

steering angle.

Transmitter

Your Transmitter is an advanced controller designed for the beginner to be easy to use and tune. You will need to

follow the steps below to ensure you prepare the controller correctly for use and understand the adjustment

possibilities available.

The function switches on the transmitter

Steering Wheel

Steering Dual Rate (D/R) Reverse Switches

Trim Setup

If the steering is not straight with the transmitter on, make sure the trim dial is set to the central position and adjust

the Servo horn on the car if needed. Then make ne adjustments with the steering trim whilst driving the vehicle.

Throttle Trim

Throttle neutral adjustments can be made

by moving the throttle trim lever up for more

throttle or down for more brake.

Steering Trim

Steering neutral adjustments can be made

by moving the steering trim lever left or right.

If the wheels point left, turn

clockwise

If wheels point right, turn

anti-clockwise.

If they point straight no adjustment

required.

Throttle End Point Adjustment (EPA)

The throttle EPA allows you to adjust the maximum degree of movement of the throttle channel.

“Hi” sets the EPA for the throttle direction, “Lo” sets the EPA for the brake direction. Turn the

dial anti-clockwise to reduce or clockwise to increase the allowable degree of movement.

When using this transmitter with an electric powered vehicle, set the end points to the

maximum setting.

Turning on the power

Turn on transmitter rst and then turn on receiver.

Turn on the transmitter switch and the LED battery

indicator will light up.

Turn on the receiver. The automatic set-up of the factory

set speed control should have been completed. If you

experience any problems with the speed control settings

refer to the Electronic Speed Control Section for correct

setup information.

The Red LED will show if the

installed AA batteries have

su󰀩cient charge.

The Red LED will ash and

there will be an audible beep if

the batteries need replacing.

Power LED

You may need to setup your transmitter to ‘bind’ with the receiver if you change to a new receiver or for any reason

lose signal.

• Place the transmitter and the receiver close to each other (within one meter).

• Turn the power switch on the transmitter to the ON position.

• Press and hold the receiver setup button, then turn the power switch to the ON position.

• The receiver LED will ash quickly. Release the setup button after 1 second.

• Press and hold the binding button on the transmitter for 1 second until the LED on the

receiver is continuously lit.

Fail Safe Setup

Caution

Any new binding of transmitter & receiver will clear the pre-set fail safe.

• With the transmitter and car switched on, press the setup button on the receiver then release. LED will ash.

Electric setup

• Leave throttle trigger in neutral position, and press the setup button. The LED will ash quickly. Once the

receiver LED remains lit, then release the setup button on the receiver.

Nitro setup

• Hold full brake on the transmitter, and press the setup button. The LED will ash quickly. Release full brake on

the transmitter once the receiver LED remains lit, then release the setup button on the receiver.

Binding the Transmitter and Receiver

Turning o the power

Turn o󰀨 receiver rst and then turn o󰀨 transmitter.

If you switch o󰀨 the transmitter rst before the R/C car, you may lose control of the R/C car.

• Turn o󰀨 the receiver switch.

• Turn o󰀨 the transmitter switch.

• Disconnect the battery connector from the speed control connector.

Installing the Transmitter Batteries

Open the battery holding

tray to expose the empty

battery slots.

Insert 4 AA batteries

into the marked spaces.

Please note the correct

direction of the batteries

Incorrect battery insertion

could damage the transmitter

2.4Ghz technology has done

away with the need for long

extendable aerials. The Aerial

on your transmitter is located

internally

Produktspezifikationen

Marke:	Maverick
Kategorie:	ferngesteuertes Spielzeug
Modell:	MTX-244
Produkttyp:	Transmitter
Produktfarbe:	Schwarz
Akku-/Batterietyp:	AA
Typ:	Radio-Controlled (RC) Model Accessories & Supplies
Menge pro Packung:	1 Stück(e)
Anzahl Kanäle:	3 Kanäle
Anzahl unterstützter Akkus/Batterien:	4
Vorgesehene Verwendung:	Auto
Markenkompatibilität:	Maverick
Batterien erforderlich:	Ja
HF-Übertragungsfrequenz:	2400 MHz