MB Quart RA1-1100.4 Bedienungsanleitung
Lies die bedienungsanleitung für MB Quart RA1-1100.4 (2 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 14 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 7.5 Bewertungen. Hast du eine Frage zu MB Quart RA1-1100.4 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Connect the RCA cables to the
INPUT connectors.
Signal Input
Connection
8
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Chassis Ground
5
7
6
4
POWER
Turn the LEVEL control completely
counter-clockwise to minimum.
Level Control
9
INPUT
LEVEL
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper cable.
Power cable size and fuse size based on a 17ft power (B+) (OFC) cable length and
18-inch ground (OFC) oxygen free cable.
Any other lengths used please consult a certied professional installer.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Disconnect
Negative Battery
Terminal
Run Cables
Mount Amplier
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when disconnected from
battery power. This is an anti-theft feature. Before unplugging power, you must
determine if your radio/source unit requires a reset code. Check the operation
manual for your vehicle or contact the dealer.
1
2
3
4ga
Cable Size
RA1-150.2
RA1-280.4
RA1-1100.4
RA1-300.1
RA1-750.1
RA1-1500.1
RA1-710.5
20 a External
40 a External
90a E xternal
40 a External
80 a External
80 a External
150a Ex ternal
Congratulations on your choice of a MBQuart amplier. This “Quick Start
Installation” guide is meant to help you “hook up” and play music. For more
detailed information, on system setting, speaker and subwoofer conguration
and full specications by model please visit our website at www.MBQuart.com
Model Fuse Size
Connect the power cable to the positive
battery terminal. The power cable must
be fused within 18 inches of the battery
terminal.
Re-connect the negative battery
terminal making sure it is securely
tightened.
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
10
11
2ch - Full Range
4ch - Full Range
4ch - Mixed Mono
Mono
5 ch
BRIDGED
CH1 CH2
BRIDGED
CH1 CH2
BRIDGED
CH3 CH4
BRIDGED
CH3 CH4
BRIDGED
CH1 CH2
SPEAKER OUTPUT
Speakers Subwoofer
CH 1
CH 2
CH 3
CH 4
CH 5
FULL
HP
LP
CROSSOVER
MODE
SUBSONIC
FREQUENCY
LOW PASS
FREQUENCY
50Hz 250Hz
Set INPUT MODE switch to 4CH.
Set CH3&4 LOW PASS MODE.
Set INPUT MODE switch to 4CH.
Set CH3&4 LOW PASS MODE.
Set INPUT MODE to 5CH.
Set CH1&2 and CH3&4 CROSSOVER switch to HP.
Common System Setup
Setup
Quick Start
Installation Guide
The illustrations below describe the various controls. Refer to
the illustration that matches your amplier.
The level control purpose is to match the output of your source signal to the
amplier. Refer to the section C for detailed instructions.
This switch will set the amplier to have a full frequency output or to lter out high
or low frequencies.
The Bass EQ control will increase the power output at 45Hz for more pronounced
bass. Exercise caution when using this control. Increase the level in small
amounts until distortion is noticed, then back off a little.
1. If possible, with the source unit off, conrm that the primary volume control is
turned down (counter clockwise).
2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or “0” adjustment. Make sure that the green LED on
the end of the amplier is illuminated.
3. Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5. Increase the amplier gain (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple ampliers.
Settings
B
This is a critical step to insure your amplier
is properly adjusted to match the signal
output level of your source unit.
THIS IS NOT A VOLUME CONTROL!
Level Setting
C
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
MBQuart products are designed and engineered in the USA by
www.maxxsonics.com
MBQ RA1 QSG 01 - rev2
MIN MAX
1
2
5
LEVEL Adjustment
RA1-300.1 / RA1-750.1 / RA1-1500.1
RA1-280.4/RA1-1100.4 RA1-710.5
RA1-150.2
X-OVER Switch
BASS BOOST
The Low Pass Filter will cut off the frequencies above the setting. The High Pass
Filter will cut off the frequencies below the setting.
The Subsonic Switch will cut off the frequencies below the setting.
3
4
Frequencies Adjustment
SUBSONIC Switch
To gain access to the RA1
amplier series top mount setting
control panel carefully remove
the four screws and lift the face
plate up.
When you’re nished with the control
panel mindfully put the face plate
back together with the four screws.
Make sure not to over tighten.
Some models include a bass
remote. Avoid adjusting the bass
remote while operating vehicle.
REM turn on
SIGNAL SENSE ON, High level
input DC turn in
Open Control
Panel
Remote Level
Control
Turn on Mode
A
D
E
3
1
4
5
2
3
1
1
1
4
5
3
3
2
2
3
1
5
2 2
3 3
1 1
5
5
RA1-150.2
RA1-280.4
RA1-1100.4
RA1-300.1
RA1-750.1
RA1-1500.1
RA1-710.5
Produktspezifikationen
| Marke: | MB Quart |
| Kategorie: | Empfänger |
| Modell: | RA1-1100.4 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit MB Quart RA1-1100.4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger MB Quart
31 Mai 2025
31 Mai 2025
31 Mai 2025
31 Mai 2025
30 Mai 2025
30 Mai 2025
30 Mai 2025
30 Mai 2025
7 September 2024
5 September 2024
Bedienungsanleitung Empfänger
- HiFi ROSE
- Devialet
- Unison Research
- Loxjie
- Denon
- Hyundai
- Intertechno
- Panduit
- Graupner
- ESX
- Amazon
- Medion
- Scansonic
- LogiLink
- Denver
Neueste Bedienungsanleitung für -Kategorien-
19 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025