Mean Well NDR-120-12 Bedienungsanleitung

Mean Well Kabel für Computer und Peripheriegeräte NDR-120-12

Lies die bedienungsanleitung für Mean Well NDR-120-12 (3 Seiten) kostenlos online; sie gehört zur Kategorie Kabel für Computer und Peripheriegeräte. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 2 Bewertungen. Hast du eine Frage zu Mean Well NDR-120-12 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/3

Installation Manual

 Type：NDR DIN rail power supply（Series：NDR-75, 120, 240, 480）

NDR-75-12 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 12V 6.3A

NDR-75-24 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 3.2A

NDR-75-48 INPUT: 100-240VAC 1.6A 50/60Hz OUTPUT: 24V 1.6A

NDR-120-12 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 12V 10A

NDR-120-24 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 24V 5A

NDR-120-48 INPUT: 100-240VAC 2.6A 50/60Hz OUTPUT: 48V 2.5A

NDR-240-24 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 24V 10A

NDR-240-48 INPUT: 100-240VAC 2.8A 50/60Hz OUTPUT: 48V 5A

NDR-480-24 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 24V 20A

NDR-480-48 INPUT: 100-240VAC 5.3A 50/60Hz OUTPUT: 48V 10A

 Introduction

NDR is a DIN rail power supply series with an economical price and slim design. Like other Mean Well’s DIN series,

they can be mounted on a TS35 Standard DIN rail.

 Installation

（1）Always allow good ventilation clearances, 5mm left and right, 40mm above and 20mm below, around the unit

in use to prevent it from overheating. Also a 10-15 cm clearance must be kept when the adjacent device is a

heat source.

（2）The appropriate mounting orientation for the unit is vertical, the input terminals at the bottom and output on

the top. Mounting orientations other than that, such as upside down, horizontal, or table-top mounting, is not

allowed.

（3）Use copper wire only, and recommended wires are shown as below.

AWG 18 16 14 12

Rated Current of

Equipment (Amp)

7A 10A 15A 20A

Cross-section of

Lead(mm

)

0.8 1.3 2.1 3.3

Note: Current each wire carries should be de-rated to 80% of the current suggested

above when using 5 or more wires connected to the unit.

Make sure that all strands of each stranded wire enter the terminal connection and the screw terminals are

securely fixed to prevent poor contact. If the power supply possesses multi-output terminals, please make

sure each contact is connected to wires to prevent too much current stress on a single contact.

（4）Use wires that can withstand temperatures of at least 80°C, such as UL1007.

（5）Recommended wire strapping length is 5mm (0.197”).

（6）Recommended screwdriver is 3mm, slotted type.

Installation Manual

（7）The recommended torque setting for terminals is shown as below.

Model I/P O/P

NDR-75 6.9 kgf-cm (6 Lb-in) 6.9 kgf-cm (6 Lb-in)

NDR-120 7.5 kgf-cm (6.5 Lb-in) 7.5 kgf-cm (6.5 Lb-in)

NDR-240 7.5 kgf-cm (6.5 Lb-in) 7.5 kgf-cm (6.5 Lb-in)

NDR-480 10.35 kgf-cm (9 Lb-in) 10.35 kgf-cm (9 Lb-in)

（8）Suggested fuse and maximum number of the PSUs that can be connected to a circuit breaker at 230V are shown

as below.

Model Fuse

Circuit breaker

C16 D16

NDR-75 T3.15A/L250V 6 13

NDR-120 T4A/L250V 5 10

NDR-240 T5A/L250V 4 10

NDR-480 T8A/L250V 3 5

（9）Mounting Instruction：

Mount as shown in figure only, with input terminals down, or else sufficient cooling will not be possible.

Admissible DIN rail：TS35/7.5 or TS35/15

For rail fastening：

（a）Tilt the unit slightly rearwards.

（b）Fit the unit over top hat rail.

（c）Slide it downward until it hits the stop.

（d）Press against the bottom for locking.

（e）Shake the unit slightly to check the locking action.

（10）For other information about the products, please refer to www.meanwell.com for details.

 Warning / Caution !!

（1）Risk of electrical shock and energy hazard. All failure should be examined by a qualified technician. Please do

not remove the case of the power supply by yourself!

（2）Risk of electric arcs and electric shock (danger to life). Connecting both the primary and the secondary sides

together is not allowed.

（3）Risk of burn hazard. Do not touch the unit in operation and shortly after disconnection!

（4）Risk of fire and short circuit. The openings should be protected from foreign objects or dripping liquids.

（5）Only install the unit in a pollution degree 2 environment (Note.1).

（6）Please do not install the unit in places with high moisture or near the water.

"Click"

Produktspezifikationen

Marke:	Mean Well
Kategorie:	Kabel für Computer und Peripheriegeräte
Modell:	NDR-120-12
Breite:	40 mm
Tiefe:	113.5 mm
Gewicht:	600 g
Produktfarbe:	Metallisch
Höhe:	125.2 mm
Energieschutzeigenschaften:	Over voltage, Overheating, Overload, Short circuit
AC Eingangsspannung:	115 - 230 V
AC Eingangsfrequenz:	47 - 63 Hz
Betriebstemperatur:	-20 - 70 °C
Relative Luftfeuchtigkeit in Betrieb:	20 - 95 %
Temperaturbereich bei Lagerung:	-40 - 85 °C
Luftfeuchtigkeit bei Lagerung:	10 - 95 %
Geräuschpegel:	- dB
Mittlere Betriebsdauer zwischen Ausfällen (MTBF):	456300 h
Eingangsstrom:	1.3 A
Sicherheit:	Ul508, TUV EN60950-1 approved ;(meet EN60204-1)
Lüfterdurchmesser:	- mm
Gesamtleistung:	120 W
Haltezeit:	16 ms
Effizienz:	85.5 %
Anstiegszeit:	60 ms