Mean Well RPD-60A Bedienungsanleitung

Lies die bedienungsanleitung für Mean Well RPD-60A (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht klassifiziert. Dieses Handbuch wurde von 28 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 14.5 Bewertungen. Hast du eine Frage zu Mean Well RPD-60A oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Installation Manual

Type：

：

：

：：Medical Switching Power Supply

(1)Enclosed (Families: MSP)

(2)Modular (Families: MP, NMP)

(3)PCB (Families: MPS, MPD, MPT, MQ, RPS, RPD, RPT, RPTG, NEM, PM)

(4)Adaptor (Families: GSM, MES)

Installation

(1)Enclosed Type

(a)Before any installation or maintenance work, please disconnect your system from the utility.

Ensure that it cannot be re-connected inadvertently!

(b)Mounting orientations other than standard orientation or operate under high ambient

temperature may increase the internal component temperature and will require a de-rating in

output current. Please refer to the specification sheets to receive the optimum mounting

position and information about the de-rating curve.

(c)Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance

must be kept when the adjacent device is a heat source.

(d)Keep enough insulation distance between mounting screws and internal components of

Enclosed units. Please refer to case drawing on specifications to receive the maximum length of

mounting screw.

(e)Recommended wires of Enclosed units are shown as below.

AWG 18 16 14 12 10 8

Rated Current of

Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A

Cross-section of

Lead(mm2) 0.75 1.00 1.5 2.5 4 6

Note: The suggested maximum current above only suit for 1-4 strips, 5 or more

strips should not exceed 80% of current rating.

Make sure that all strands of each stranded wire enter the terminal connection and the screw

terminals are securely fixed to prevent poor contact.

(f)For other information about the products, please refer to www.meanwell.com for details.

(2)Modular Type

(a)Before any installation or maintenance work, please disconnect your system from the utility.

Ensure that it cannot be re-connected inadvertently!

(b)Mounting orientations other than standard orientation or operate under high ambient

temperature may increase the internal component temperature and will require a de-rating in

output current. Please refer to the specification sheets to receive the optimum mounting

position and information about the de-rating curve.

(c)Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance

must be kept when the adjacent device is a heat source.

(d)Keep enough insulation distance between mounting screws and internal components of

Modular units. Please refer to case drawing on specifications to receive the maximum length of

mounting screw.

(e)Recommended wires of Modular units are shown as below.

AWG 18 16 14 12 10 8

Rated Current of

Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A

Cross-section of

Lead(mm2) 0.75 1.00 1.5 2.5 4 6

Note: The suggested maximum current above only suit for 1-4 strips, 5 or more

strips should not exceed 80% of current rating.

Make sure that all strands of each stranded wire enter the terminal connection and the screw

terminals are securely fixed to prevent poor contact.

(f)For other information about the products, please refer to www.meanwell.com for details.

Produktspezifikationen