Megger ICLAMP Bedienungsanleitung

Lies die bedienungsanleitung für Megger ICLAMP (7 Seiten) kostenlos online; sie gehört zur Kategorie Messung. Dieses Handbuch wurde von 5 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 8 Bewertungen. Hast du eine Frage zu Megger ICLAMP oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

GSafety Warnings

These safety warnings are provided to ensure

the safety of personnel and proper operation of

the instrument.

nSafety warningsand precautionsmust

be read

and understood before the ICLAMP

is used. They must be observed during use.

nDo not leavethe ICLAMP connected to the

system under test when not in use.

nDo not touchcircuit connections and

exposed metalwork of the installation or

equipment under test.

nDo not usethe ICLAMP or connect it to any

external system if it shows any visible signs of

damage or if it has been stored for prolonged

periods in unfavourable conditions.

nDo not usethe ICLAMP or connect it to any

external system if the casing is open or any

parts of the case are missing.

nDo not usethe ICLAMP or connect it to any

external system if the ICLAMP lead is damaged

inany way.

nDo not usethe ICLAMP on live electrical

conductors.

nAlwaysconnect the ICLAMP to the DET

instrument before clamping it around the

item being tested.

nAlwaysinspect the DET instrument, ICLAMP

and connection cable prior to everyuse.

Replace any defective parts immediately.

nAlwaysuse extreme caution when clamping

around bare conductors: under fault conditions,

potentially high voltages and currents may be

present and may pose a shock hazard.

NOTE: THE INSTRUMENT MUST ONLY BE

USED BY SUITABLY TRAINED AND

COMPETENT PERSONS.

Users of this equipment and/or their employers

are reminded that National Health and Safety

Legislation requires them to carry out valid risk

assessments of all electrical work so as to

identify potential sources of electrical danger

and risk of electrical injury such as inadvertent

short circuits. Where the assessments show

that the risk is significant then the use of fused

test leads may be appropriate.

The safety warnings provided in this document

are indicative of safe practice and shall not be

considered exhaustive. Additionally, they are

not intended to replace local safety procedures

where the instrument is being used.

Symbols used on the ICLAMP are:

G

Caution: refer to accompanying notes

tEquipment protected throughout by

Double Insulation

cEquipment complies with current EU

directives

Do not dipose of in the normal waste

stream

Equipment can be clamped around and

removed from hazardous live conductors

(IEC 61010-2-032 Type A clamp)

Equipment not suitable for use

where the magnetic field

exceeds this limit

Overvoltage category IV is for

equipment installed at or near the

origin of the electrical supply to a

building

600 V refers to the rms phase-to-

earth voltage that this instrument

can withstand to the over

voltage

categor

yIV rating

M

Megger Limited

Archcliffe Road, Dover

K

ent CT17 9EN

England

T+44 (0)1 304 502101

F

+44 (0)1 304 207342

E

uksales@megger.com

Megger

4271 Bronze Way, Dallas,

Texas 75237-1019

USA

T+1 214 333 3201

T+1 800 723 2861 (USAonly)

F+1 214 331 7399

Eussales@megger.co

Megger

Z.A. Du Buisson de la Couldre

23 rue Eugène Henaff

78190 TRAPPES

France

T+33 (0)1.30.16.08.90

F+33 (0)1.34.61.23.77

Einfos@megger.com

Megger Pty Limited

Unit 26 9 Hudson Avenue

Castle Hill

Sydney NSW 2125

Australia

T+61 (0)2 9659 200

F+61 (0)2 9659 2201

Eausales@megger.com

Megger Limited

110 Milner Avenue Unit 1

Scarborough Ontario M1S 3R2

Canada

T+1 416 298 9688 (Canada only)

T+1 416 298 6770

F+1 416 298 0848

Ecasales@megger.com

Megger products are distributed in 146 countries worldwide.

This instrument is manufactured in the USA.

The company reserves the right to change the

specification or design without prior notice.

Megger is a registered trademark

Part No. 6172-967_SW_V05 Printed in England 1209

www.megger.com

ICLAMPSAFETY WARNINGS

M

G

>100 A/m

CAT IV

600 V

Produktspezifikationen