Meliconi Control 2+ Bedienungsanleitung

Meliconi Fernbedienung Control 2+

Lies die bedienungsanleitung für Meliconi Control 2+ (5 Seiten) kostenlos online; sie gehört zur Kategorie Fernbedienung. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 2 Bewertungen. Hast du eine Frage zu Meliconi Control 2+ oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/5

Control 2.1

Thank you for choosing a Meliconi remote control.

The Control 2.1 remote control is designed to command and a DECODER (satellite or digital terrestriala TV ).

The remote control has a permanent memory, so it does not lose its settings even if there are no batteries in . it

The MELICONI remote control reproduces infrared signals corresponding to the original; the functions that operate in radio

frequency (e.g. voice commands and pointers) are not supported.

The remote control requires 2 new 1.5V alkaline batteries, not included in the AAA/LR03

package. Insert with the correct polarity as shown in gure.

DO NOT use batteries. rechargeable

BATTERIES TEST: Press and hold the 5 button and check that the LED remains on

continuously until the button is released. If the light is o or blinks, the inserted batteries are low,

therefore they need replacement.

WARNING:

As the remote control is capable of controlling 2 devices, during setup (and also during normal use), you must select the

operation mode then dene which device you want to control. (TV / STB) ;

To select the operation mode, press the button quickly and repeatedly until the LED corresponding to

the device you want to operate is switched on. ( led / led) TV = red STB = green

Before using the remote control, for each device you wish to control, it is to set a it matched. essential specic code,

Identify the specic code and set it into the remote control using one of the following ways:

MANUAL

SMARTPHONE

TABLET - WEB

ACTIVATION OF REMOTE CONTROL

SELECTION OF OPERATING MODE

Do not leave exhausted batteries inserted, as liquid may leak and damage the remote control

INSERTING THE BATTERIES

SAFETY WARNINGS

The remote control and batteries should not be exposed to excessive heat such as sunlight, re

or the like.

The product . Keep out of reach of children or domestic animals. is not a toy

Keep this booklet for future reference

Use the -code on the side or connect to the page and follow the instructions. qr www.cme.it

Once you have found the specic code for your device, set it in the remote control as described in the

ENTERING THE CODE DIRECTLY chapter.

ATTENTION : searching for the suitable code could last up to 5 minutes.

• Stand in front of the device to be controlled and make sure it is ON (not in stand-by). If necessary, switch

it on using the original remote control (if this is still working) or the buttons present on the device itself. (on

TVs they can be on the side or the top)

• On the MELICONI remote control and then press and hold the butt until select the operating mode on

the LED of the remote control lights up; lease. re

• Pointing the remote control towards the device, PRESS AND HOLD butt and wait the ON/OFF on

(even up to 5 minutes) for the device to switch o.

• , w the device turn oIMMEDIATELY RELEASE the button. PAY ATTENTION hen ,

• Three nal ashes indicate that the operation has been completed successfully.

(only to be performed if you know the to be set) specic code

• On the MELICONI remote control and then press and hold the button until select the operating mode

the LED lights up; release.

• Immediately enter the previously identied specic code.

• Three nal ashes indicate that the operation has been completed successfully.

If necessary it is possible to reset the remote control and bring it back to the initial conditions. completely

WARNING : All user settings will be lost. Operate as follows:

• On the MELICONI remote control press and hold the button until the LED lights up; release.

• Enter the code . 0100

• Three nal ashes indicate that the operation has been completed successfully.

RESET THE REMOTE CONTROL

If the remote control does NOT carry out the three nal ashes, the setting is NOT successful; repeat the procedure.

If still unsuccessful, it means that the code is not included in the remote control, contact the ASSISTANCE.

ENTERING THE CODE DIRECTLY

VERIFY

Check that the MELICONI remote control operates your device the main functions if it does not, the in ; REPEAT

procedure.

NOTE: When the list of codes to be searched is over, the remote control exits the search and the LED remains o.

If no results are obtained, try using the procedure described in the SMARTPHONE - TABLET - WEB chapter or contact

the ASSISTANCE.

MANUAL SEARCH

SMARTPHONE - TABLET - WEB

watch

the video

watch

the video

The functions of the buttons on the MELICONI remote control are only available if the original device is equipped with it.

Sometimes some functions of the original remote control are not directly present on the MELICONI remote control keypad.

To enable them, connect to the page, use the on-line tool ACTIVATION OF REMOTE CONTROL and continue www.cme.it

until you see the list matching buttons between the original remote control and the MELICONI remote control.

If the function you want to play is matched with an number i color operate as follows: n orange ,

• On the MELICONI remote control and then press and hold the button. select the operating mode

• When the LED turn on , point the remote control towards the device , without releasing the button

and enter the previously identied number corresponding to the function you want to get. (at the last digit

pressure, the remote control already transmits this function)

• Release the buttons; to match the function obtained to a MELICONI remote control button, within 30

seconds, press and hold the desired button.

• Wait three ashes indicate that storage; release the button. (the used button loses the original function

that will be called by setting again the activation code)

For any future activation of the remote control, it is advisable to extract and note the code in use, operate as follows:

• On the MELICONI remote control and then press and hold the select the operating mode

button until the LED lights up; release.

• Enter the code . 0010

• After a pause of several seconds, the LED produces four sets of ashes, spaced out,

corresponding to the code to be obtained. Count the number of ashes. Each set of ashes

corresponds to one digit in the code. Ten ashes correspond to the digit 0 . zero “ ”

( code obtained = example 1701)

• Make a note of the code obtained. You may need it in future.

If you want to delete the function in combination with a single button, operate as follows:

• On the MELICONI remote control and then press and hold the button. select the operating mode

• When the LED turn on enter the code ; release the buttons. , without releasing the button, 1600

• Within 30 seconds, press and hold the button of which you want to delete the function; wait three ashes indicating the end

of the operation, release the button. (to recall the original function, setting again the activation code)

Using the MELICONI remote control to command 2 devices (TV and DECODER) it is often necessary to select the operating

mode before to operate on the corresponding device.

To avoid this uncomfortable and frequent operation, it is possible to combine in a single keyboard two dierent modes of use.

Automatically the keys will control the TV, while the remaining keys will be the DECODER. V+ V-

Operate as follows:

• On the MELICONI remote control press and hold the button until the LED lights up; release.

• Enter the code . 0069

• Three nal ashes indicate that the operation has been completed successfully.

To obtain a function related to the other mode of use, for example the function of the DECODER, press and ON/OFF

hold the button and press the desired key ( + ).

To return to operate in the two distinct mode of use, carry out the procedure using the code . 0096

COMBINED KEYPAD

DELETE FUNCTION BY SINGLE BUTTON

DISPLAY CODE IN USE

BUTTONS AND FUNCTIONS

watch

the video

Produktspezifikationen

Marke:	Meliconi
Kategorie:	Fernbedienung
Modell:	Control 2+
Produktfarbe:	Schwarz
Akku-/Batterietyp:	AAA
Akku-/Batterietechnologie:	Alkali
Menge pro Packung:	1 Stück(e)
Verpackungsart:	Box
Anzahl unterstützter Akkus/Batterien:	2
Akku-/Batteriespannung:	1.5 V
Schnittstelle:	IR Wireless
Markenkompatibilität:	Universal
Maximale Reichweite:	- m
Wiederaufladbar:	Nein
Anzahl der unterstützten Geräte:	2
Beleuchtete Tasten:	Nein
Fernbedienung Nutzung:	TV, TV set-top box
Eingangssignal:	Drucktasten