Metra 99-3527 Bedienungsanleitung
Metra
Nicht kategorisiert
99-3527
Lies die bedienungsanleitung für Metra 99-3527 (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 17 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 9 Bewertungen. Hast du eine Frage zu Metra 99-3527 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
REV. 3/9/2016 INST99-3527
Installation instructions for part 99-3527
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• A) Radio housing • B) Trim plate • C) ISO brackets
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • GMOS-01 • GMOS-04
Antenna Adapter: • 40-GM10
• Phillips screwdriver • Panel removal tool • 9/32” socket wrench
TOOLS REQUIRED
Pontiac Grand Prix 2004-2008
99-3527
A B C
Dash Disassembly ..................................................2
Kit Assembly
– DIN radio provision with pocket ............................ 3
– ISO DIN radio provision with pocket ...................... 3
Table of Contents
99-3527
2
1. Remove the bezel from around
the key cylinder. (Figure A)
2. Unclip and remove the entire
panel surrounding the radio,
including the
message center
and the vents. (Figure B)
3. To remove the radio, start at
bottom of the stack and remove
(8) 9/32” screws from the pocket,
climate control, and the radio.
(Figure C)
Continue to kit assembly
Dash Disassembly
(Figure B) (Figure C)
(Figure A)
99-3527
Kit Assembly
(Figure A) (Figure A)
(Figure B) (Figure B)
DIN radio provision with pocket
1. Remove the metal DIN sleeve from
the aftermarket radio.
2. Slide the sleeve into the radio
housing and secure by bending the
metal locking tabs down
. (Figure A)
3. Slide the radio back into the sleeve
until it clicks in. (Figure B)
4.
Locate the factory wiring harness
and antenna connector in the
dash and complete all necessary
connections to the radio and climate
controls. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Test the radio for
proper operation
.
5. Reassemble the dash in reverse
order of disassembly.
ISO DIN radio provision with pocket
1.
Remove the metal DIN sleeve and
trim ring from the aftermarket radio
2.
Secure the to the ISO brackets
radio with the screws supplied with
the radio. (Figure A)
3.
Slide the radio into the radio
housing until the side clips engage.
(Figure B)
4.
Snap the into the trim plate radio
housing. (Figure B)
5.
Locate the factory wiring harness
and antenna connector in the
dash and complete all necessary
connections to the radio and climate
controls. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Test the radio for
proper operation
.
6. Reassemble the dash in reverse
order of disassembly.
3
Produktspezifikationen
| Marke: | Metra |
| Kategorie: | Nicht kategorisiert |
| Modell: | 99-3527 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Metra 99-3527 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Metra
15 Juli 2025
5 Juli 2025
5 Juli 2025
5 Juli 2025
5 Juli 2025
5 Juli 2025
1 Juli 2025
27 Juni 2025
8 Juni 2025
8 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- PolyScience
- Aduro
- Vincent
- Sprolink
- Di4
- Rolling Square
- Sunset
- TEAC
- Ibico
- Glem Gas
- Peavey
- Paingone
- Numatic
- Fontiso
- Lexibook
Neueste Bedienungsanleitung für -Kategorien-
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025