Microchip MIC22705YML Bedienungsanleitung
Seiten 9 Englisch Nicht kategorisiert
Lies die Bedienungsanleitung für Microchip MIC22705YML kostenlos online oder lade das PDF herunter. 55 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
MIC22705YML EV
Evaluation Board
1MHz, 7A Integrated Switch High-
Efficiency Synchronous Buck Regulator
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (
408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
February 2011 M9999-020411-A
General Description
The Micrel MIC22705 is a high-efficiency, 7A, integrated
switch, synchronous buck (step-down) regulator. The
MIC22705 achieves more than 95% efficiency and
switches at 1MHz. The ultra-high speed control loop keeps
the output voltage within regulation even under the
extreme transient load swings commonly found in FPGAs
and low-voltage ASICs. The output voltage is pre-bias safe
and is adjustable down to 0.7V.
The MIC22705 offers a full range of sequencing and
tracking options. The Enable/Delay (EN/DLY) and Power
Good (PG) inputs allow versatile turn-on and turn-off
sequencing across multiple devices. The Ramp Control™
(RC) input allows start-up voltage tracking, either directly
or ratio-metrically.
The MIC22705 is available in a 24-pin 4mm x 4mm MLF®
with a junction operating range from –40° °C to +125C.
Data sheets and support documentation are found on the
Micrel web site: www.micrel.com.
Requirements
The MIC22705YML EV requires a power supply of 2.9V to
5.5V, and a test load. Ensure that the power supply can
provide the wattage required for the chosen test load. The
load can be active (electronic load) or passive (resistor).
Additionally, monitor the Power Good output (PG) with a
multimeter or an oscilloscope if desired.
Precautions
There is no reverse input protection on this board. When
connecting supplies and signals ensure that correct
polarities are observed.
Getting Started
1. VIN Supplies
Connect the VIN supply (2.9V to 5.5V) across the PVIN and
PGND terminals. Monitor VIN at the PVIN and PGND
terminals with a voltmeter.
2. Enable/SHDN Inputs
The enable input EN is internally pulled up with a 1µA
current source. When external on/off control is desired,
install Q1 and R5, and connect a logic level control signal
to the SHDN input. When SHDN is high, the output is off,
and when SHDN is low, the output is on.
3. Monitor Outputs
Monitor the output VOUT with a scope or DVM connected
across the VOUT and PGND terminals.
4. Output Load
Connect a load across the VOUT and PGND terminals.
Use an active or passive load.
5. Turn On the Power
Turn on the power supply and verify that VOUT = 1.8V.
Ordering Information
Part Number Description
MIC22705YML EV Evaluation Board for the MIC22705YML
Produktspezifikationen
| Marke: | Microchip |
| Kategorie: | Nicht kategorisiert |
| Modell: | MIC22705YML |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Microchip MIC22705YML benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Microchip
Microchip TC7652 Bedienungsanleitung Microchip PAC1720 Bedienungsanleitung Microchip TC4428A Bedienungsanleitung Microchip ATSAM4LS2C Bedienungsanleitung Microchip MCP6S91 Bedienungsanleitung Microchip dsPIC33FJ32GS610 Bedienungsanleitung Microchip PIC32MK1024MCF064 Bedienungsanleitung Microchip ATSAME53J19A Bedienungsanleitung
Beliebt in Nicht kategorisiert
Microchip SY88149CL Bedienungsanleitung Microchip PIC16F1508 Bedienungsanleitung Microchip UTC2000 Bedienungsanleitung