Microchip PIC10F222 Bedienungsanleitung
Seiten 4 Nicht kategorisiert
Lies die Bedienungsanleitung für Microchip PIC10F222 kostenlos online oder lade das PDF herunter. 8 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
2004 Microchip Technology Inc.DS51491A-page 1
PROGRAMMING PIC10F2XX DEVICES WITH
THE BASELINE FLASH MICROCONTROLLER
PROGRAMMER (BFMP)
INTRODUCTION
The Baseline Flash Microcontroller Programmer (BFMP) together with the PICkit
™
1 Baseline Flash Programmer PC
application is designed to program baseline PIC10F2XX Flash devices.
PICkit
™
1 FIRMWARE REVISION 2.0.0.
When the PICkit1 PC application is executed with the BFMP connected to a USB port, the firmware version is displayed
in the bottom left corner of the interface window, as shown in Figure1. If “Firmware Version 2.0.0.” or greater is
displayed, the programmer is ready for use. If lower version number is displayed, disconnect any PICkit 1 Flash demo
boards connected to USB. If the interface window states that the programmer can not be found, check all connections
between the PC, any USB hubs and the BFMP.
FIGURE 1:FIRMWARE VERSION
PIC10F2XX PROGRAMMING
The 6 and 8-pin PIC10F2XX devices require an adapter socket to connect the device to the 6-pin connector at the end
of the BFMP. The user can elect to purchase an adapter board from Microchip (see Universal Programming Adapter
below) or build one using the information in this document.
The procedure for programming a PIC10F2XX device is as follows:
1.Load the PICkit
1 Baseline Flash Programming PC application onto a PC with a Windows
®
98 SE or later
Operating System.
2.Connect the BFMP to the PC using a regular USB cable.
3.Connect the BFMP to the target device through the 6-pin connector on the BFMP, using an appropriate program-
ming adapter.
4.Start the PC application.
5.The application should correctly identify the BFMP firmware version. If not, remove any PICkit boards attached
to the PC and check all USB connections, then restart the application.
6.Select the appropriate device from the Device Configuration window (see Figure1).
7.Load the hex file using the pull-down File menu on the PC application toolbar.
8.Click on the Write device button.
9.The Progress Bar should grow from left to right until programming is complete.
10.Once programming is complete, the Status Bar should turn green.
11.If not, check all connections to the BFMP and the target device.
Note:The PICkit1 Baseline Flash Programming PC application can be downloaded from the Microchip
Technology Inc. web site at www.microchip.com.
Information Sheet
Produktspezifikationen
| Marke: | Microchip |
| Kategorie: | Nicht kategorisiert |
| Modell: | PIC10F222 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Microchip PIC10F222 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Microchip
Microchip ATMXT3072M1 Bedienungsanleitung Microchip HT12-100S0s/TE08030502 Bedienungsanleitung Microchip LE79272 Bedienungsanleitung Microchip USB7052N Bedienungsanleitung Microchip AT91SAM7SE32 Bedienungsanleitung Microchip WBZ350UE Bedienungsanleitung Microchip PIC18F13K50 Bedienungsanleitung Microchip AT32UC3C2512C Bedienungsanleitung
Beliebt in Nicht kategorisiert
Microchip SY88149CL Bedienungsanleitung Microchip PIC16F1508 Bedienungsanleitung Microchip UTC2000 Bedienungsanleitung