Monacor PREAMP-1UP Bedienungsanleitung
Lies die bedienungsanleitung für Monacor PREAMP-1UP (2 Seiten) kostenlos online; sie gehört zur Kategorie Regler. Dieses Handbuch wurde von 20 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 10.5 Bewertungen. Hast du eine Frage zu Monacor PREAMP-1UP oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Technical data S.1/2
Preamplifier PREAMP
Technical modifications reserved 07/04
Thank you for buying a WHD product. Please read this manual carefully,especially the ! marked parts.
Content :
PREAMP CD500 uP ... :
Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.Accessory subframe
CD500 ,colour : “ alpinweiss “
PREAMP uP ... :
Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.
Colour : “ alpinweiss “
The subframes are not available at WHD.
PREAMP BJ uP ... :
Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.
Colour : “ alpinweiss “
The subframes are not available at WHD.
Specifications :
Supply voltage : 22-26V
Output voltage : 5V max.
Output impedance : 50 Ω
Input voltage Line : 400 mV
Input voltage Mic : 4mV
Frequency range Line : 20-20 000 Hz (-1dB)
Frequency range Mic : 40-15 000 Hz (-3dB)
Current consumption : 0,025 A
Terminal : 7 -pole terminal , removeable
Control voltage : 0-10VDC
Additional parts : ( JUNG/CD500 frames and UP-cabinets KAISER available at WHD)
Subframe Frame
single Frame
double UP-cabinet
61/63 mm
X X X
X X X
The microphone volume control has a combined ON-OFF switch.
Technical data - S. 2/2 - Pre- amplifier PREAMP ...
Technical modifications reserved 07/04
Mounting :Mounting :
Connect terminal according to wiring scheme.
Backside view
Backside view
Note : The control terminal no. 4 gets a voltage of 12V by an internal resistor. So the preamplifier
has the maximum gain at open terminal.
Terminal no
1 + Signal – out ( unbalanced )
2 0 Signal
3 Reduced gain
4 + Control input 0-12 VDC
5 0 V Control
6 0 Supply voltage
7 + 24V Supply voltage
8 0 V Phantom / Mic
9 + Mic input
10 + 24V Phantom
If the gain is too high for some applications , connect the accessory wire bridge to terminal 3 and 5.
This will reduce the gain to app. 1/3.
Note : Teminal 8 to 10 is only for use with input balance unit.
For the signal and control line we recommend shielded cable.
e.g. LIYCY 0.14mm² 2-cores
The cross section of the power supply cable should be adequate.
e.g. H03VV-F 0,5mm² 2-cores
We recommend regulated 24VDC power supply with short circuit protection.
Produktspezifikationen
| Marke: | Monacor |
| Kategorie: | Regler |
| Modell: | PREAMP-1UP |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Monacor PREAMP-1UP benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Regler Monacor
18 August 2024
16 August 2024
14 August 2024
12 August 2024
11 August 2024
11 August 2024
10 August 2024
10 August 2024
10 August 2024
8 August 2024
Bedienungsanleitung Regler
- Sven
- KanexPro
- Thrustmaster
- Denon
- Heritage Audio
- StarTech.com
- Asus
- RCA
- Saramonic
- Krom
- Samsung
- SmartAVI
- Sonifex
- Hikvision
- Draper
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
5 Oktober 2024
4 Oktober 2024
3 Oktober 2024
1 Oktober 2024
Hori Force Feedback Truck Control System Bedienungsanleitung
1 Oktober 2024
30 September 2024
27 September 2024