Moxa MGate 5101-PBM-MN Bedienungsanleitung

Moxa Nicht kategorisiert MGate 5101-PBM-MN

Lies die bedienungsanleitung für Moxa MGate 5101-PBM-MN (6 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 8 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 4.5 Bewertungen. Hast du eine Frage zu Moxa MGate 5101-PBM-MN oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/6

P/N: 1802051010014

*1802051010014*

MGate 5101- - PBM MN Series

Quick Installation Guide

Vers 20ion January 3.2, 21

Technical Support Contact Information

www.moxa.com/support



2 . A 20 1 Moxa Inc ll rights reserved.

- - 2

Overview

The MGate 5101-PBM-MN is an industrial Ethernet gateway for

PROFIBUS- - - to Modbus TCP network communication.

Package Checklist

Before installing the MGate 5101-PBM-MN, verify that the package

contains the following items:

• -PBM- 1 MGate 5101 MN gateway

• i g Quick nstallation uide (printed)

• Warranty Card

Please notify your sales representative if any of the above items are

missing or damaged.

Optional Accessories (can be purchased separately):

• - - - - - - CBL F9M9 150: DB9 female to DB9 male serial cable, 150 cm

• - - - - - - CBL F9M9 20: DB9 female to DB9 male serial cable, 20 cm

• - - - - - Mini DB9F to TB: DB9 female to terminal- block connector

• - - - WK 36 01: Wall mounting kit

Hardware Introduction

LED Indicators

LED

Color

Function

PWR1

Green

Power is on

Off

Power is off

PWR2

Green

Power is on

Off

Power is off

Ready

Green

Steady on: Power is on and the MGate is

functioning normally

Blinking: The MGate has been located by the

MGate Manager’s Location function

Red

Steady on: Power is on and the MGate is booting

Blinking: Indicates an IP conflict, or the DHCP or

BOOTP server is not responding properly

Off

Power is off or fault condition exists

COMM

Off

No data exchange

Green

Data exchange with all slaves

Green,

flashing

Data exchange with at least one slave (not all

configured slaves can communicate with gateway)

Red

Bus control error

CFG

Off

No PROFIBUS configuration

Green

PROFIBUS configuration OK

PBM

Off

PROFIBUS master is offline

Red

PROFIBUS master is in STOP mode

Green,

flashing

PROFIBUS master is in CLEAR mode

Green

PROFIBUS master is in OPERATE mode

TOK

Green

Gateway holds the PROFIBUS token

Off

Gateway is waiting for the PROFIBUS token

- - 3

LED

Color

Function

Ethernet

Amber

Steady: 10Mbps, no data is transmitting

Blinking: 10Mbps, data is transmitting

Green

Steady: 100Mbps, no data is transmitting

Blinking: 100Mbps, data is transmitting

Off

Ethernet cable is disconnected

Reset Button

The reset button is used to load factory defaults. Use a pointed object

such as a straightened paper clip to hold the reset button down for five

seconds. Release the reset button when the Ready LED stops blinking.

Hardware Installation Procedure

STEP 1 :

C -onnect the power adapter. Connect the 12 48 VDC power line

or DIN

-rail power supply with the MGate -PBM-5101 MN

device’s terminal block.

Make sure the adapter is connected to

an earthed socket.

STEP 2:

Use a PROFIBUS cable to connect the unit to a PROFIBUS slave

device.

STEP 3 :

Connect the unit to the Modbus TCP device.

STEP 4

The

MGate -PBM- 5101 MN series is designed to be

attached to

a DIN

- rail or mounted on a wall. For DIN rail

mounting, push

down the spring and properly attach it to the

-DIN

rail until it

“snaps” into place. For wall

mounting, install the wall-mount

kit (optional) firs

t and then screw the device onto the wall.

Wall or Cabinet Mounting

Two metal plates are provided for mounting the

unit on a wall or inside a cabinet. Attach the plates

to the unit’s rear panel with screws. With the plates

attached, use screws to mount the unit on a wall.

The heads of the screws should be 5 to 7 mm in

diameter, the shafts should be 3 to 4 mm in

diameter, and the length of the screws should be

more than 10.5 mm.

For each screw, the head should be 6 mm or less in diameter, and the

shaft should be 3.5 mm or less in diameter.

Produktspezifikationen

Marke:	Moxa
Kategorie:	Nicht kategorisiert
Modell:	MGate 5101-PBM-MN
Gewicht:	500 g
Betriebstemperatur:	0 - 60 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Temperaturbereich bei Lagerung:	-40 - 85 °C
Abmessungen (BxTxH):	36 x 105 x 140 mm
Eingangsspannung:	12 - 48 V
Sicherheit:	UL 60950-1, EN 60950-1
Höhe bei Betrieb:	0 - 2000 m