Moxa NPort 5210A Bedienungsanleitung

Lies die bedienungsanleitung für Moxa NPort 5210A (4 Seiten) kostenlos online; sie gehört zur Kategorie Server. Dieses Handbuch wurde von 29 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 6 Bewertungen. Hast du eine Frage zu Moxa NPort 5210A oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

— 1— — 2 — — 3 —

NPort 5200A Series

Quick Installation Guide

First Edition, July 2010

1. Overview

NPort 5200A series device servers are compact, palm-sized data

communication devices that allow you to control RS-232 (NPort 5210A),

RS-422/485 (NPort 5230A), and RS-232/422/485 (NPort 5250A) serial

devices over a TCP/IP-based Ethernet.

Note: “-T” indicates an extended temperature model.

2. Package Checklist

Before installing the NPort 5200A series device server, verify that the

package contains the following items:

y1 NPort 5200A serial device server

yPower Adaptor (NPort 5200A-T doesn't include this accessory)

y4 stick-on pads

yDocument & Software CD

yQuick Installation Guide

yProduct Warranty Statement

Optional Accessory

yDK-35A: DIN-Rail Mounting Kit (35 mm)

Notify your sales representative if any of the above items are missing or

damaged.

3. Hardware Introduction

As shown in the following figures, NPort 5200A series device servers

have two male DB9 ports for transmitting RS-232 (NPort 5210A), or

RS-232/422/485 (NPort 5250A) serial data and have two 5-pin terminal

block ports for transmitting RS-422/485 (NPort 5230A).

Power input

RJ45 10/100M Ethernet port

Reset button

Rear Panel View

Top Panel View

DIN-Rail

screw hole

Wallmount

screw hole

Terminal Block

Stick-on pad

Male DB9 serial port

Front Panel View

NPort 5210A/5250ANPort 5230A

Reset Button—Press and hold the Reset button for 5 seconds to load

factory defaults: Use a pointed object, such as a straightened paper clip or

toothpick, to depress the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds).At this point, release the reset

button.

LED Indicators—NPort 5200A’s top panel has four LED indicators,

which are described in the following table.

LED

Name

LED

Color

LED Function

Steady on:

Power is on and the NPort is booting up.

Red

Blinking:Indicates an IP conflict, or DHCP or

BOOTP server is not responding properly.

Steady on:Power is on and the NPort is functioning

normally.

Green

Blinking:The NPort has been located by the NPort

Administrator’s Location function.

Ready

Off Power is off, or a power error..

Orange

10 Mbps Ethernet connection.

Green

100 Mbps Ethernet connection.

Link

Off Ethernet cable is disconnected.

Orange

Serial port is receiving data.

Green

Serial port is transmitting data.

P1, P2

Off

No data is being transmitted or received through the

serial port.

Adjustable pull high/low resistor and terminator for RS-422/485

Port 1Port 2

Remove the NPort 5230A/5250A’s top

cover and you will find DIP switches to

adjust each serial port’s pull-high, pull-low,

and terminator. Do not use the 1 KΩ setting

with RS-232 mode, as doing so will

degrade the RS-232 signals and shorten the

communications range.

ON

123

1 2 3

SW

Pull-high resistor Pull-high resistor Terminator

ON 1 KΩ 1 KΩ 120Ω

OFF *150 KΩ *150 KΩ *---

*Default

P/N: 1802052000010

Produktspezifikationen