My Wall HP 60 L Bedienungsanleitung

Lies die bedienungsanleitung für My Wall HP 60 L (2 Seiten) kostenlos online; sie gehört zur Kategorie Wandstütze. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 3.7 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu My Wall HP 60 L oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Reset Mode

Disconnect the power supply cord. Wait for 10 seconds and reconne button for 5 seconds until you hear a long OK

beep. The mount starts to move upward to the highest position and thx emits a beep. Then moves downward to the

lowest position and the control box emits twice beeps.

NOTE: No-load running prohibited!

Before power connection, be sure that bracket and the TV installed correctly.

Keep the children away from power.

!

Upward Movement

Press and hold the button to lift themount.

(Tips: Clear up all obstacles

within the range of motion.)

Memory Setting 1

Press the button for 2 seconds until you hear a

beep, indicating that the current position

has been saved to memory.

Recall Memory

Press the button and the mount will

automatically get to the position saved

in the corresponding button . Press mem1

any button to stop motion.

Recall Memory

Press the button and the mount will automatically

get to the position saved in the corresponding

button . Press any button to stop motion.mem2

Memory Setting 2

Press the button for 2 seconds until

you hear a beep, indicating that the

current position has been saved to

memory.

Downward Movement

Press and hold the button to lower the mount.

(Tips: Clear up all obstacles within the range of motion.)

OK Button

Short press the button and the mount will automatically retract

to the highest position. Press any button to stop motion.

2x AAA battery (not included)

HP 60 L

Coding of Remote Controller and Control Box

Step 1: When the mount is powered on, press the small button on the control box with a thin tool as shown.

The unit emits a beep, indicating that the control box is on standby for program coding.

Step 2: Press the button on the remote control, and the control box repeatedly beeps for approximate 10 seconds SET

indicating that the remote control is being programmed. The process will be nished automatically until you can‘t hear

a beep any longer.

NOTE: Clear up the historical data when replacing a new remote control to pair. Press the small button on the control

box with hearing a beep, and hold for 10 seconds to conrm the data-cleaning process is completed until you hear two

beeps.

Possible reasons caused by TV mount or remote control.

TV MOUNT

1.)The system may be overheating. Check if the unit beeps two times after pressing the button. If so, allow the unit to cool down and return to

room temperature (about 12 minutes).

2.)The AC/DC end of the power cord may be unplugged/disconnect from the outlet/mount. Check the connection to the outlet/mount to

ensure the unit has power.

1.)Check to see if a foreign object is impeding the mount from moving. If so, remove the object.

2.)The weight of TV may exceed the maximum weight limitation of the mounting system.

3.)The motor wire may be broken. Reset the system. If the problem still exists, contact your place of purchase for replacement.

1.)Check all power connections and reset the system. If the unit continues to make an abnormal noise, please contact your place of

purchase for a replacement.

REMOTE CONTROL

1.)The remote control operating distance may be too far and not in range of the mount. Acceptable range should be less than 10m (30 feet).

2.)The batteries in the remote control may be low or dead. Replace the batteries.

3.)The remote control may be broken. Check to see if the indicator LED found on the remote lights when a button is pressed. If not, contact your place of

purchase for a replacement.

The motorized TV mount does not respond to remote control.

The TV mount stops moving during operation and emits a long beep.

The TV mount is making an abnormal noise or sound.

If a problem arises, please try the troubleshooting guidelines below. If the problem is not listed, please contact your

local distributor for additional technical assistance.

Hereby, Transmedia Kabelverbindungen GmbH declares that the lift stand type HP 60 L is in compliance

with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:

https://www.transmedia-germany.com/downloads/download/docs/CE_HP60L_20051501.pdf

revised 1

18.05.2020

Produktspezifikationen