Native Trails Topanga VNA201 Bedienungsanleitung
Native Trails
Nicht kategorisiert
Topanga VNA201
Lies die bedienungsanleitung für Native Trails Topanga VNA201 (1 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 2 Bewertungen. Hast du eine Frage zu Native Trails Topanga VNA201 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
When cleaning up after installations, DO NOT USE ABRASIVE CLEANERS, as they may scratch and change the vanity surface.
Use warm water, a soft cloth and a non-abrasive soap to clean the surface.
Refer to the Care and Maintenance Instructions for more information.
Installation Instructions
Topanga and Vintner’s Floating Vanities
• It is strongly recommended that Native Trails wall mount vanities are installed by a licensed contractor.
• Observe all local plumbing and building codes.
• Have a licensed contractor determine if the wall is strong enough to adequately hold the weight of a full wall
mount and applicable accessories.
• Ensure proper access to the final plumbing connections.
• Place a protective covering on the floor to prevent damage, unpack and inspect the wall mount for any damage.
CAUTION: Risk of personal injury. Native Trails Wall Mounts are extremely heavy, obtain sufficient help when lifting
or moving.
CAUTION: Risk of property damage. Make sure that watertight seals exist on all drain connections, and that
flooring, walls, and adjacent cabinetry are adequately protected while installing.
Tools Needed:
Level
Pencil
Measuring Tape
Stud Finder
Drill
Materials Recommended:
±8 - 4.5" Fastenmaster HeadLOK
Heavy-Duty Flathead Fasteners Screws
General Instructions:
3.
Hang vanity by connecting French Cleat (A) and French Cleat (B)
securely into each other. Check with Level again and adjust
slightly if needed.
4. Install at least two 4.5" screws per stud through the vanity and
into French Cleat (A) to secure the vanity to the studs.
(Figure 2)
1. Mark the height and width of the vanity on the wall at
the desired height in coordination with the location
of the studs.
2.
Use a Level and attach French Cleat (B) to wall into the
studs using at least two 4.5" screws per stud.
(Figure 1)
Figure 1
Figure 2
4.5"
Screws
French
Cleat
(B)
French
Cleat
(A)
Vanity
4.5"
Screws
French
Cleat
(B)
Wall Studs
Produktspezifikationen
| Marke: | Native Trails |
| Kategorie: | Nicht kategorisiert |
| Modell: | Topanga VNA201 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Native Trails Topanga VNA201 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Native Trails
24 Juli 2025
24 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- Thermalright
- Futurelight
- COMSOON
- Navman
- Irritrol
- Envertech
- Rega
- Stamos
- WARN
- Brüder Mannesmann
- MagnaPool
- Smart Media
- Pelgrim
- Magic Chef
- Electrolux
Neueste Bedienungsanleitung für -Kategorien-
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025
26 Juli 2025