NAV-TV GVIF-RR NTV-KIT167 Bedienungsanleitung
NAV-TV
Nicht kategorisiert
GVIF-RR NTV-KIT167
Lies die bedienungsanleitung für NAV-TV GVIF-RR NTV-KIT167 (6 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 32 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 16.5 Bewertungen. Hast du eine Frage zu NAV-TV GVIF-RR NTV-KIT167 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/6
BHM
01/07/13
NTV-DOC158
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for :
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
1 | P a g e
3950 NW 120th Ave, Coral Springs, FL 33 TEL 561-955-9770 FAX 561-955-9760 065
www.nav-tv.com info@nav-tv.com
GVIF- RR
NTV-KIT 167
Overview
The GVIF- Kit allows the user to add up to 3 video inputs and a backup camera input to the RR
factory media screen in select Range Rover (LR3/HSE) vehicles. This kit has a dedicated rear
view camera input, 3 composite (RCA) audio/video inputs, an RGB input and an AV output with
AV switching.
Kit Contents
AV Input Harness
Power/CAN Harness
LVDS Video cable
GVIF- Interface RR
Remote
RGB Input cable
Input Toggle Switch
IR Eye Harness
BHM
01/07/13
NTV-DOC158
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for :
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2 | P a g e
Interface Connectors
Dip Switch Sengs* Congure prior to installaon
Dip SW:
1
2
3
4
5
6
7
8
UP
Enables
RGB
Enables
V1
Enables
V2
Enables
V3
Land Rover
Aermarket
NAV
Factory or
no Rev-Cam
N/A
DOWN
Skips
RGB
Skips
V1
Skips
V2
Skips
V3
Lexus
Factory
NAV
Acvates
aermarket
Rev-Cam
N/A
AV IN/OUT
Power/CAN
Dip Switches
Status LEDs
*Note: If the dip switches are not congured prior to
installaon you must remove power to the unit prior to
making adjustments to the dip switches. When power is
reconnected aer the dip switch adjustment the new
sengs will be stored into memory.
LCD IN/OUT
(LVDS Cable)
BHM
01/07/13
NTV-DOC158
Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for :
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3 | P a g e
Installaon
THIS INTERFACE INSTALLS AT THE NAV DRIVE UNDER THE SEAT AT THE SCREEN , NOT !
1. Locate the factory NAV drive under the driver/passenger seat.
2. Gather the provided from the GVIF-RR kit. Connect the following ‘Power/CAN Harness’
wires to the car:
Note: CAN connecon is not supported at this me. You must connect the GRAY wire
to a reverse lamp for reverse acvaon!
3. Disconnect the factory LVDS cable from the NAV drive, this is oen a black or blue
connector.
4. Connect the provided LVDS male side (labeled ‘LRIN’) of the
video cable to the factory NAV drive. Be certain you’re inserng
this connector properly, it is keyed but it may sll be ght!
5. Connect the free end (removed in step 3) of the factory video cable to the female side of
the provided LVDS video cable (labeled ‘LROUT’).
6. Connect the white end of the LVDS video cable to the interface at the port labeled ‘LVDS
IN/OUT’ Note: If aer installaon you receive a ‘NAV NOT AVAILABLE’ message, the .
LVDS cables may not be seated fully.
7. Connect the AV Input cable to the port on the GVIF- interface labeled RR ‘AV IN/OUT’. If
you’re only connecng a reverse camera (and no other
inputs), the signal input from the camera must connect
to the RCA labeled . Refer to the dip-‘REAR-C’
switch sengs chart to skip/enable AV sources
upon toggle switch presses (oponal. Page 2 ).
8. Adjust dip switches on the GVIF-RR interface properly, refer to the chart on page 2 for
qualicaons.
9. Connect the white plug from the to the port on the GVIF-‘Power/CAN Harness’ RR
interface labeled ‘Power/CAN/RGB’.
10. Mount the interface down where it will not interfere with seat movement or passengers
feet.
Interface wires
Connect to car
Black (GND)
Chassis Ground
Red (ACC)
Accessory
Gray (Rear)
Reverse lamp 12v (+)
Produktspezifikationen
| Marke: | NAV-TV |
| Kategorie: | Nicht kategorisiert |
| Modell: | GVIF-RR NTV-KIT167 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit NAV-TV GVIF-RR NTV-KIT167 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert NAV-TV
14 August 2024
9 August 2023
9 August 2023
9 August 2023
9 August 2023
9 August 2023
9 August 2023
9 August 2023
9 August 2023
9 August 2023
Bedienungsanleitung Nicht kategorisiert
- MIPRO
- Donexon
- Scheppach
- Boss
- Bravilor Bonamat
- Signature Hardware
- Tiger
- Venom
- Intesis
- Ooni
- Varytec
- Maretron
- Dux
- Aduro
- Stenda
Neueste Bedienungsanleitung für -Kategorien-
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025
19 Juni 2025