Neewer RGB176-A1 Bedienungsanleitung
Seiten 1 Beleuchtung
Lies die Bedienungsanleitung für Neewer RGB176-A1 kostenlos online oder lade das PDF herunter. Diese Anleitung wurde 0 Mal aufgerufen. Frage zu diesem Modell? Stelle eine Frage

Press the "CCT" button
briefly to enter CCT mode,
then press the "" button
briefly until the " " icon
flashes on the screen.
Rotate the "" button to
adjust the color
temperature value.
Thank you for purchasing the NEEWER RGB176-A1 LED light!
RGB176-A1 is an RGB full color LED light with a built-in battery, which can be
used both indoors and outdoors. It has the much sought after CCT , HSI and
SCENE modes allowing users to create a colorful lighting environment.
RGB176-A1 LED light ×1Ball Head Adapter ×1
USB cable ×1
Soft Diffuser
Screw into the 1/4" threaded
hole at the bottom of the
light body and tighten the
knob.
Loosen the knob to adjust
the light angle and tighten
to hold in position.
Follow the direction of the
arrow facing upwards to
slide the diffuser out of
the slot to remove.
Reverse to install.
Long press the " " button
for 2 seconds to turn the
LED light on/off.
Charging
Switch ON/OFF
Brightness Adjustment
CCT Mode Adjustment
Plug the USB cable into
the USB port of the light
and connect it to a power
supply to charge the light.
Remove the cold shoe
adapter completely from
the bottom of the light
and screw the light directly
on the top of the light
stand via the 1/4" threaded
hole.
Insert the cold shoe adapter
of the light, which is a flat
square piece, into the
camera hot shoe mount
and tighten the knob.
Soft Diffuser ×2
Saturation Adjustment
Red & Green
Compensation Value
Adjustment
Hue Adjustment
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generes, uses and can radiate radio at
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit diff
erent from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for
an uncontrolled environment.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
IC Warning Statements
- English Warning Statement
“This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.” The digital
apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This radio transmitter has been approved by Industry Canada to operate with
the antenna types listed with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum
gain indicated for that type, are strictly prohibited for use with this device.
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
- French Warning Statement
“Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
mêmesi le brouillage est susceptible d'en compromettre le fonctionnement.”
Cet appareil numérique de la classe B est conf
orme à la norme NMB-003 du
Canada.
Le présent émetteur radio a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le
gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
L'équipement a été évalué comme satisfaisant aux exigences générales en
matière d'exposition aux radiofréquences. L'appareil peut être utilisé sans
restriction dans des conditions d'exposition portatives.
Slot
On/Off Button
Scene Button
Color
Temperature
Button
HSI Button
USB Charging Port
Screen
1/4" Threaded Hole
Short press:
Toggle beween
settings within
a mode
Rotate:
Adjusting setting
values
In any mode, short press
the "" button until the
"" icon flashes, rotate
the "" button to adjust
the brightness setting
value.
Short press the "HSI" button
to enter HSI mode. Press
the " " button briefly until
the "S" icon flashes. Rotate
the "" button to adjust
the saturation setting.
Short press the "HSI" button
briefly to enter HSI mode.
Press the " " button briefly
until the "H" icon flashes.
Rotate the "" button to
adjust the hue setting.
FX Mode Adjustment
Short press the "FX" button
to enter FX mode, then
rotate the "" button
until the scene icon flashes
on the screen to switch
between different scenes.
Bluetooth Connection
Press and hold the " "
button to turn on the
device. The " " icon will
flash to indicate that
connection via Bluetooth
is possible. Connect to the
light from the "NEEWER"
APP using your Smartphone
for wireless control. For
additional information,
please scan the QR code
of the "APP guide page"
on the APP prompt card.
RGB176-A1Model
10W
Rated Power
97
98
CRI
TLCI
[email protected](1100LX)
Max. Illumination
2500K~10000K
Color Temperature Adjustment
0%-100%(in 1% increments)
Brightness Adjustment
0~360°
Hue Adjustment
17
-50~+50
Number of Scenes
Red & green Compensation Value
7.4V/3200mAh/23.68Wh
Built-in Battery
DC 5V/2A, 9V/2A
Type-C
Charging Input
Charging Port
1. Installing the soft diffuser
2. Installing the ball head adapter3. Installing the light on the camera
4.Installing on a tripod
Press the "CCT" button
briefly to enter CCT mode,
then press the "" button
briefly until the "GM" icon
flashes. Rotate the ""
button to adjust the red
and green compensation
values.
1. Do not place the product in an environment where the temperature
exceeds 40℃/ 104°F.
2.Do not drop the product on the ground, or subject it to a strong physical
impact.
3. Do not look directly at the light when using the product to avoid possible
visual impairment.
4. Do not use the product in the rain or in a humid environment.
5. Do not modify the circuit board or disassemble the product .
6. Unplug the power cord when not in use.
7. If you do not intend to use the product for a long time, keep it in a ventilated,
dry place, away from heat and magnetic fields.
Specifications
How to Use
How to Use
How to Use
How to UseHow to Use
Notes
About this product
Package Contents
Product Illustration
How to AssembleHow to Assemble
How to Assemble
Scene modes
Lightning
Hue flash
CCT loopINT loopTV screenPartyFireworks
CCT PulseHUE PulseCop carCandlelightHUE loop
Paparazzi
Defective
bulb
ExplosionWeldingCCT Flash
EN
ENENEN
EN
EN
01
04
0506
0203
Produktspezifikationen
| Marke: | Neewer |
| Kategorie: | Beleuchtung |
| Modell: | RGB176-A1 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Neewer RGB176-A1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten