Nemco 8075SXW-RC Bedienungsanleitung
Nemco
hotdogmaschine
8075SXW-RC
Lies die bedienungsanleitung für Nemco 8075SXW-RC (3 Seiten) kostenlos online; sie gehört zur Kategorie hotdogmaschine. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Nemco 8075SXW-RC oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/3
Model Series: 8050SX-RC, 8075SXW-RC, Flat Roller Grills
8050SX-SLT-RC, 8075SXW-SLT-RC Slant Roller Grills
INTRODUCTION
1. Please read instructions before using.
2. This roller grill will be HOT during use and for a short time after it is turned off – BE CAREFUL!
INSTALLATION
1. Set the roller grill on a flat surface.
2. Position the roller grill near the power outlet. Avoid the use of extension cords.
3. Plug the roller grill into a certified electrical outlet with a corresponding voltage rating as listed on the
roller grill model label.
4. Clean the roller grill thoroughly before use.
OVERVIEW OF CONTROLS
1. This machine has two zones, a front zone which is closest to the controls, and a rear zone which is
furthest from the controls. Each zone is designated by the color of the bearings, black bearings for the
front zone, and white bearings for the rear zone.
2. There are two lighted rocker switches to turn the motors on, one for each zone.
3. There are two thermostats to turn the heat on, one for each zone.
4. There are two pilot lights to indicate when the heat is on, one for each zone.
5. There is also a display that shows the approximate temperature of the zone once it reaches temperature.
This display has two lights that cycle back and forth to indicate which zone’s temperature is being
displayed. This display is an approximation; product should be probed with a thermometer to verify that
it is above the safe serving temperature.
STARTUP
1. Turn on/off switches to the on position and make sure rollers are turning.
2. Turn temperature controls to desired temperature
♦ Knob setting #2: temperature is approximately 140º ; HOLD
♦ Knob setting #4: temperature is approximately 160º ; HOLD
♦ Knob setting #6: temperature is approximately 200º ; REHEAT
♦ Knob setting #8: temperature is approximately 250º ; REHEAT
3. Allow rollers to heat for 5 to 10 minutes before placing product on rollers.
4. Plastic tongs are included with the units. Use plastic to prevent serious damage to these rollers. Never
use metal utensils or tools on the GripsIt rollers.
5. Once the product has finished reheating; turn the grill down to the hold zone. Never leave product on
reheat as it will overcook the product and dry it out.
2
CLEANING
1. Turn the temperature controls on high and turn the rollers on before cleaning.
2. ALWAYS START AT THE END OF THE ROLLERS AND WIPE TOWARD THE CENTER. This prevents
extra grease from entering the sides of the roller grill and into the bearings.
♦ Use a wet, soft cloth to wipe the rollers clean. NOTE: never use any metal object on the GripsIt rollers
at any time. Metal will cause serious damage to the rollers.
3. After cleaning the rollers, remove the drip pan and clean with mild soap and water.
SERVICE INSTRUCTIONS
PREVENTATIVE MAINTENANCE
NOTE: Proper maintenance plays an important part in the life span and functioning of the roller grill.
1. The chains that drive the rollers should be inspected and greased once a year to be sure that they
continue to operate correctly. This will allow the machine to operate for a much longer time.
2. IMPORTANT: Disconnect the roller grill from the power source before disassembly.
3. Nemco offers a greasing kit, ordering number 80586. Alternatively, any food grade grease with a
temperature rating of at least 500°F can be used to grease the chains.
IF ROLLERS WON’T TURN
1. Check power source to be sure the roller grill is plugged into the proper voltage outlet and that the outlet
is in proper working order.
2. IMPORTANT: Disconnect the roller grill from the power source before disassembly.
3. Remove the end covers.
4. If the drive chain is off the idler sprocket, reinstall it.
5. Remove the drive chain from the sprocket on the motor shaft and if the rollers turn easily, then replace
the motor.
6. Remove the chain guard and inspect the sprockets on the end of each roller. If they are loose, worn, or
out of alignment, then replace the roller.
7. If the rollers are hard to turn by hand (without the chain attached) remove and clean out any
accumulated foreign matter in the bearings and on the rollers.
8. IMPORTANT: Reassemble the roller grill completely before reconnecting to the power source.
IF ROLLER GRILL BLOWS A FUSE OR CIRCUIT BREAKER
1. Check the capacity of the circuit being used to be sure it is not overloaded.
2. Unplug the roller grill and check it’s wiring for short circuits.
IF ROLLERS WON’T HEAT
Check the power source to be sure the roller grill is plugged into the proper voltage outlet and the receptacle
is working. If properly connected and still no heat call NEMCO customer service at 1-800-782-6761.
Produktspezifikationen
| Marke: | Nemco |
| Kategorie: | hotdogmaschine |
| Modell: | 8075SXW-RC |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Nemco 8075SXW-RC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung hotdogmaschine Nemco
22 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
5 Juli 2025
5 Juli 2025
Bedienungsanleitung hotdogmaschine
- Guzzanti
- Trisa
- Ambiano
- Hyundai
- Saro
- Lagrange
- Star
- Avantco
- APW Wyott
- Carnival King
- Vollrath
- Grand Slam
- Benchmark USA
Neueste Bedienungsanleitung für -Kategorien-
22 August 2025
21 August 2025
21 August 2025
21 August 2025
19 Juli 2025
17 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025
7 Juli 2025