Netgear GS116 Bedienungsanleitung
Netgear
Nicht kategorisiert
GS116
Lies die bedienungsanleitung für Netgear GS116 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 42 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 21.5 Bewertungen. Hast du eine Frage zu Netgear GS116 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
)NSTALLATION'UIDE
NETGEAR 16-port Gigabit Switch Model GS116
Estimated Time: 5–10 minutes
Unpack the Box and Verify the Contents
When you open the box, verify that you received everything. The package includes:
• NETGEAR 16-port Gigabit Switch Model GS116
• AC power adapter
• Wall-mounting screws
• GS116 Installation Guide (this document)
• Warranty/support information card
If you do not have everything listed above, see the support information card for contact
information. If you are missing the support information card, get contact information at
http://www.NETGEAR.com in the Technical Support section.
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface such as a table,
desk or shelf. The switch comes with wall-mounting screws. You can use the screws if you
want to hang the switch in an open space on a wall.
Make sure the selected location is:
• Not in direct sunlight or near a heater or heating vent.
• Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on
all sides of the switch.
• Well ventilated (especially if it is in a closet).
Also, you will need one Category 5 (Cat 5) Ethernet cable with RJ-45 connectors for each
device you want to connect to the switch. Each Ethernet cable must be less than 328 feet
(100 meters).
Install the Switch and Connect the Other Devices
1. Place the switch on a flat surface or hook onto the screws.
2. For each device, insert one end of an Ethernet cable into the port in the device and
insert the other end into one of the Ethernet ports on the switch.
3. Connect the power adapter cord into the back of the switch and then plug the adapter
into a power source (such as a wall socket or power strip).
The Power light should light up.
4. Check the LEDs to confirm that all connections are correct.
LED Activity
Power • On: 16-port Gigabit Switch has power.
•Off: No power.
RJ-45 ports • Right LED on: 10 Mbps connection to a powered device.
•Left LED on: 100 Mbps connection to a powered device.
•Both LEDs on: 1000 Mbps connection to a powered device.
•Blink: Activity on this port.
072
!UTO
5PLINK
-BPS'IGABIT3WITCH
'3
/N,INK
"LINK!CT
"OTH-
--
6 $# !
,/#!,
-
).4%2.%4
/&& /.
072
!UTO
5PLINK
-BPS'IGABIT3WITCH'3
/N,INK
"LINK!CT
"OTH-
--
Power
Troubleshooting
Technical Support
Thank you for selecting NETGEAR products.
After completing the Smart Wizar e the serial number on the d configuration assistant, locat
bottom label of your product, and use it to register your product at
http://www.NETGEAR.com/register.
Registration on the website or over the phone is required before you can use our telephone
support service. The phone numbers for worldwide regional customer support centers are
on the Warranty and Support Information card that came with your product.
Go to http://kbserver.netgear.com for product updates and Web support.
Problem Action
Power light is not lit The switch has no power. Make sure that:
• The power cord is properly connected to the switch.
• The power adapter is properly connected to a functioning power
outlet. If it is in a power strip, make sure the power strip is turned
on. If the socket is controlled by a light switch, make sure the
switch is in the on position.
• You are using the NETGEAR power adapter supplied with your
switch.
Port number light is
not lit for a connected
device, or stays on
continuously
There is a hardware connection problem.
• Make sure the cable connectors are securely plugged in at the
switch and the device.
• Make sure the connected device is turned on.
• If the Ethernet cable is connected to a NIC or other Ethernet
adapter, make sure the card or adapter is installed correctly and
is working.
• Make sure the cable is less than 328 feet (100 meters).
Produktspezifikationen
| Marke: | Netgear |
| Kategorie: | Nicht kategorisiert |
| Modell: | GS116 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Netgear GS116 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Netgear
26 September 2025
26 September 2025
25 September 2025
25 September 2025
20 September 2025
16 September 2025
7 September 2025
26 Juli 2025
25 Juli 2025
25 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- Coline
- Luna Optics
- Kruidvat
- Peavey
- Eberle
- Drive Medical
- Cambo
- Zebra
- Fuxtec
- FoxFury
- Steinbach
- Be You
- Connection
- Omron
- GFB
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026