Netgear ProSafe WAC740 Bedienungsanleitung

Lies die bedienungsanleitung für Netgear ProSafe WAC740 (2 Seiten) kostenlos online; sie gehört zur Kategorie Zugangspunkt. Dieses Handbuch wurde von 32 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 4 Bewertungen. Hast du eine Frage zu Netgear ProSafe WAC740 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Installation

NETGEAR ProSAFE Dual Band Wireless AC

Access Point

WAC740

Set Up the Access Point

Before mounting the access point in a high location, first set up and test the

access point to verify WiFi network connectivity.

IMPORTANT: You can deploy the WAC740 access point only in a WiFi

network that is managed by a ProSAFE wireless controller.

¾To cable the access point:

1. Connect an Ethernet cable from LAN port 1 on the access point to a

LAN port on a PoE+ switch, that is, an 802.3at-compatible switch.

2. Connect an Ethernet cable from the PoE+ switch to an Ethernet port on

the computer.

3. Check the LEDs to verify that the access point is set up correctly.

LED Description

Power LED

•O. Power is o.

•Solid green. Power is on.

•Alternating green and amber. The access point is receiving insucient

PoE power.

•Solid amber, then blinking amber. A self-test is running or firmware is

being loaded. During startup, the Power LED first lights solid amber, then

goes o, and then blinks amber before turning solid green aer about

one minute. If aer two minutes the Power LED remains solid amber or

continues to blink amber, it indicates a system fault.

Activity LED

•O. No link with the network is detected.

•Solid green. A link with the network is detected.

•Blinking green. Network trac is detected.

Package Contents

Unpack the box and verify the contents:

• WAC740 ProSAFE Dual Band Wireless AC Access Point

• Category 5e Ethernet cable

• Ceiling mount kit

LED Description

LAN LED 1

•O. A 10 Mbps Ethernet link is detected or no Ethernet link is detected.

•Solid green. A 2.5 Gbps Ethernet link is detected.

•Solid amber. A 1 Gbps or 100 Mbps Ethernet link is detected.

If both LAN LED 1 and LAN LED 2 light solid green or amber, the LAN ports

are members of a link aggregation group (LAG).

LAN LED 2

•O. No LAG is detected.

•Solid green. A LAG with a 2.5 Gbps Ethernet link is detected.

•Solid amber. A LAG with a 1 Gbps or 100 Mbps Ethernet link is detected.

If both LAN LED 1 and LAN LED 2 light solid green or amber, the LAN ports

are members of a LAG.

2.4G WLAN LED

•O. The 2.4 GHz WiFi radio is o.

•Solid green. The 2.4 GHz WiFi radio is on.

•Blinking green. WiFi activity is detected on the 2.4 GHz WiFi radio.

5G WLAN LED

•O. The 5 GHz WiFi radio is o.

•Solid green. The 5 GHz WiFi radio is on.

•Blinking green. WiFi activity is detected on the 5 GHz WiFi radio.

The access point uses a DHCP client that is enabled by default. If your network

includes a DHCP server, the access point obtains an IP address from the DHCP

server. If your network does not include a DHCP server, the access point sets

its IP address to a static IP address of 192.168.0.160.

If your network includes a DHCP server, note the following:

• Make sure that Option 43 is enabled on the DHCP server.

• Make sure that the DHCP server specifies the IP address of the wireless

controller in the required hexadecimal format in the Option 43 field.

For example, if the IP address of the wireless controller is 192.168.0.250,

you must enter the hexadecimal string 02:04:C0:A8:0:FA.

To compose the address, start with 02:04: and then add each of the four

address octets in hexadecimal format, separated by colons.

The first two octets (02:04) define a standalone NETGEAR wireless

controller, or in a stack, the first wireless controller in the stack.

Produktspezifikationen