Nitek WB5362 Bedienungsanleitung
Nitek
WLAN-Repeater
WB5362
Lies die bedienungsanleitung für Nitek WB5362 (6 Seiten) kostenlos online; sie gehört zur Kategorie WLAN-Repeater. Dieses Handbuch wurde von 20 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 10.5 Bewertungen. Hast du eine Frage zu Nitek WB5362 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/6
WB5326
Wireless Bridge
Quick Start Guide
01/09/12
2
Quick Start Guide
WB5326 Outdoor Wireless Bridge
Items Included in Kit
(1) WB5326 RADIO
(1) PoE (48V, 1A)
(1) Mounting Hardware Accessories
(1) Quick Start Guide
(1) Product CD
Hardware Installation
1. Put an Ethernet cable with RJ-45 connector through the water-tight joint. Make the RJ-45 connector as a 568B
wiring configuration:
2. Using the hardware provided mount the Bridge unit in position. Make sure that the Ethernet connection is
facing down. Keep in mind that the unit has a built-in antenna and must have line of sight between units. Refer
to separate mounting guide sheet for illustrations of hardware assembly.
3. Plug water-tight joint side of the Ethernet cable into the Bridge unit. Connect the other end of the cable to the
power injector supplied with the unit. Also connect a standard RJ-45 network cable for the power injector to a
hub or a terminal.
4. There is a ground connection on enna port. The ground connection should the Bridge unit located near the ant
be connected to a proper earth ground point.
5. The antenna of the Bridge unit is behind the plastic face of the unit and must face the other Bridge unit. Make
sure you have line of site to the opposite unit and that they face each other.
Warning Do not mount Bridge unit near electric power lines, electric
lights or near strong electric power signals
6. Power the unit using the supplied PoE inserter.
12345678
568B
21 4
3
Terminal Wire
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Green
7 Brown/White
8 Brown
3
These instructions are designed for configuring this system to be a network Bridge.
1. Power up each Bridge unit for 30 seconds, then RESET it by pressing the Reset button for 10 seconds.
2. On the PC you will be using to setup the Bridge units, select “Network Connections” in the control Panel. You
can get to it by Start>Settings>Control Panel>Network Connections. Locate the “Local Area Connection”
and right click to select “ ”. When in that tab select “Properties Internet Protocol (TCP/IP)”.
3. Set up a computer with a network IP address of:
IP address 192.168.1.100
Subnet 255.255.255.0
Gateway 192.168.1.254
4. Select and note an IP address for each Bridge unit along with an ID name and password for each unit (see
Example 1). You will also need to select a Channel from 1-11 for all units. Bridge units are designed to work as a
pair. Both units of the pair must operate on the same channel. Different sets should use different channels. For
maximum data speed separate sets by 4 channels or more (i.e., 1, 6, 11).
* Each pair of units must operate on the same channel (1 - 11). Different pairs should use different channels.
Example 1
Unit Your IP Address
For each unit Password Unit ID Channel*
1 xxx.xxx.xxx.1 Build 1 Building One 1
2 xxx.xxx.xxx.2 Build 2 Building Two 1
3
4
5
6
Produktspezifikationen
| Marke: | Nitek |
| Kategorie: | WLAN-Repeater |
| Modell: | WB5362 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Nitek WB5362 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung WLAN-Repeater Nitek
5 August 2024
Bedienungsanleitung WLAN-Repeater
- Tenda
- Gembird
- Smart-AVI
- Vodafone
- Strong
- Iogear
- TRENDnet
- DTRONIC
- Davis
- Totolink
- ALC
- Asus
- D-Link
- Western Digital
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
13 Juni 2025
9 Juni 2025
9 Juni 2025
3 Juni 2025
31 Mai 2025
2 Dezember 2024
25 November 2024
10 Oktober 2024
3 Oktober 2024