Oliveri NP6101TH Bedienungsanleitung
Oliveri
Waschbecken
NP6101TH
Lies die bedienungsanleitung für Oliveri NP6101TH (2 Seiten) kostenlos online; sie gehört zur Kategorie Waschbecken. Dieses Handbuch wurde von 71 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 36 Bewertungen. Hast du eine Frage zu Oliveri NP6101TH oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS
CAUTION
Leave protective tape on the sink when inverting over a benchtop and tracing its shape. The stainless
steel will scratch if the sink slides across a hard surface.
Topmount sinks may also be known as “drop in” or “inset” sinks.
Topmount models with prex PR, SN, NP, MO, DZ, PE, LL, UF, PL, MR, EL & TI.
These sinks will t into standard 600mm bench tops.
Templates are available for download from www.oliverisinks.com
Download PDF template from www.oliverisinks.com. If the template is not available, the cutout shape may be created by
carefully inverting the sink onto the counter/benchtop and tracing around the perimeter.Cut the hole 10mm inside the traced line.
Many Oliveri sinks have waste outlets positioned to the rear of the bowls. Ensure the sink is correctly positioned when tting.
Unequal bowl depth:
Sinks that combine different sized bowls may also have unequal bowl depth. Waste plumbing will need to
accommodate this variance. All sinks have a height adaptor included with the sink where needed.
Solitaire models (LR)
LR510 & LR515 may be top mounted, each using a circular cutout 466mm in diameter. LR515 comes with a 32mm diameter
taphole pre-cut in the tap landing. Mark the location of this taphole when trial tting the sink. Then, drillout the counter/benchtop
in the appropriate location so that the mixer tap can be solidly installed through both the sink and the counter/benchtop.
LR510 may also be under mounted in a solid-surface counter/benchtop using a circular cut out 454mm in diameter
after edges are smoothed. Refer Oliveri undermount instructions for recommended installation methods.
MATERIALS FOR FITTING THE UNDERMOUNT SINK:
• Oliveri sink (with correct tap holes as ordered) - includes mounting clips,
sealing gasket, basket wastes and other accessories (depending on
model).
• These Installation Instructions
• Level to check counter/benchtop & sink is installed level
• Phillips head screwdriver (#2 to tighten mounting clips)
• Flat head screwdriver (large - to tighten basket wastes)
• Suitable sealant (neutral-cure silicone sealant or equivalent)
• Masking material to protect counter/benchtop and sink from excess
sealant
• Additional Mounting Hardware if tting into thinner material. The
clamps included with the sink require a minimum counter/benchtop
thickness of 25mm / 1”.
INSTALLER - PLEASE READ & FOLLOW THESE
INSTALLATION INSTRUCTIONS
Please retain for consumer as care instructions are included
IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT AT TIME OF CUTTING
Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in
relation to goods manufactured by it or their use and installation, is given in good faith and is believed by
Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,
assistance or service is provided by Tasman Sinkware without responsibility or liability.
FOR “TOP MOUNT” OR “DROP IN” SINKS
CHECK MODEL
The model number on the sink
packaging must match the model
of sink the customer ordered.
Do not install if incorrect.
AVOID CUTS
The perimeter and punch-outs on
the sink may contain sharp edges.
Handle the sink carefully to avoid
personal injury.
CHECK THE CONDITION
Inspect the sink for any visible
defects. Do not install the sink if
defects are found. Contact your
sink retailer / point of purchase.
AVOID SCRATCHES
Stainless steel can be scratched
if proper care is not taken during
installation.
Do wnload cutout
template files
(PDF, & F) DWG DX
from our website.
AUSTRALIA
Head Ofce &
Manufacturing Plant
Tasman Sinkware Pty Ltd
Regency Park SA
Phone: +61 8 8348 6444
Fax: +61 8 8348 6495
Email: [email protected]
oliveri.com.au
© Tasman Sinkware
TF 08f May 2017
Produktspezifikationen
| Marke: | Oliveri |
| Kategorie: | Waschbecken |
| Modell: | NP6101TH |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Oliveri NP6101TH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Waschbecken Oliveri
29 Juli 2025
29 Juli 2025
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
31 August 2024
Bedienungsanleitung Waschbecken
- Kuchinox
- BLANCO
- American Standard
- Enza
- Bartscher
- Franke
- TOTO
- Lynx
- Cata
- Rohl
- Coyote
- Dxv
- Schock
- Miomare
- Tot Mate
Neueste Bedienungsanleitung für -Kategorien-
9 Januar 2026
29 Dezember 2026
28 Dezember 2025
28 Dezember 2025
25 Dezember 2025
24 Dezember 2025
23 Dezember 2025
23 Dezember 2025
22 Dezember 2025
21 Dezember 2025