On-Stage SS7990 Bedienungsanleitung
On-Stage
Sprecher-Unterstützung
SS7990
Lies die bedienungsanleitung für On-Stage SS7990 (1 Seiten) kostenlos online; sie gehört zur Kategorie Sprecher-Unterstützung. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 13 Bewertungen. Hast du eine Frage zu On-Stage SS7990 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
Hanging Speaker Bracket
SS7990
©2018 The Music People On-Stage.com
1. Remove brackets and components from box
and ensure all components are included.
2. Check for stud location with a stud nder
and place wall bracket in desired location.
3. Test that the bracket is level and mark the
hole locations on the wall using the holes from
bracket as a template.
4. Drill proper mounting hole (smaller that outer
thread diameter of your lag bolts) through wall into
wood/metal studs or concrete block (lag shields not
included but recommended for concrete application.)
Hole depth should be properly drilled so the lag bolt
can go through the sheet rock and 2" into the stud.
5. Place speaker bracket on wall and install lag bolts
(recommended for stud application) in the upper
location, securing tightly until the head of the lag bolt is
rmly against the bracket. Repeat for bottom location.
6. Place the crossbar along the top of the bracket,
lining up the center hole with the bracket hole and
insert the crossbar bolt from the top through the
crossbar and bracket and secure with the locking nut.
Tighten, noting steering capability of the crossbar.
7. Prepare speakers for installation using the speaker
manufacturer recommendations and hardware, never
exceeding appropriate weight ratings for speaker
hanging. If speaker manufacturer does not carry
cables, aircraft cables are recommended. Steerable
cable kits should be used if steerable option is desired.
8. Insert the eye bolts into the side holes of the center
bracket from below and secure tightly with the locking
nuts. If tilting is desired, locate the preferred position
in the angle brace and secure the eye bolt with the
locking nut. Before hanging the speaker on the
bracket, test installation by conrming the bracket will
hold the weight of your speaker.
9. Hang the speaker according to your speaker
manufacturer’s hanging instructions and the desired
application. If unsure, contact a pro-audio professional
for proper installation. Improper hanging or use could
cause damage to equipment and/or humans.
Included:
•
x2 Wall brackets
•
x4 Lag bolts with washers
•
x2 Crossbars
•
x2 Crossbar bolts with
locking nuts
•
x3 Eye bolts with nuts
Also Required:
•
Socket/hand wrench
•
Drill
•
Drill bit
•
Stud finder
• Pencil
•
Level
•
Tape
•
Speaker Flying Hardware
½" Sheet Rock
2"
2" x 4"
Vertical
Support
Produktspezifikationen
| Marke: | On-Stage |
| Kategorie: | Sprecher-Unterstützung |
| Modell: | SS7990 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit On-Stage SS7990 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sprecher-Unterstützung On-Stage
2 Oktober 2025
Bedienungsanleitung Sprecher-Unterstützung
- USX-Mount
- Axis
- Barkan
- Rocketfish
- KEF
- Best Buy
- Vogel's
- Lowell
- Sonos
- Sanus Systems
- QSC
- Monacor
- QualGear
- Insignia
- Edbak
Neueste Bedienungsanleitung für -Kategorien-
17 Januar 2026
27 Dezember 2025
21 Dezember 2025
12 November 2025
5 November 2025
31 Oktober 2025
30 Oktober 2025
12 Oktober 2025
11 Oktober 2025
27 September 2025